898101621 Mercruiser SCREW

Required Service Tools
Table 1
Required Service Tools    
Part Number    Description    
N/A     4 mm Allen Wrench    
6V-2197     Transducer    
7X-1171     Transducer Adapter    
7X-1695     Cable As (Top Center Position)    
9U-7330
or
146-4080     Digital Multimeter Gp (RS-232)
Digital Multimeter Gp (RS-232)    
7X-1710     Multimeter Probe    
7X-1715     Adapter Cable As (40-Pin Breakout)    
7X-6370     Adapter Cable As (3-Pin Breakout)    
1U-5804     Crimp Tool (12 To 18 AWG)    
175-3700     Connector Repair Kit (Deutsch DT)    Two short jumper wires are needed to check the continuity of some wiring harness circuits by shorting two adjacent terminals together in a connector. A long extension wire may also be needed to check the continuity of some wiring harness circuits.Caterpillar Electronic Technician (ET)
Cat ET can display the following information:
Parameters
Event codes
Diagnostic codes
Engine configurationCat ET can be used by the technician to perform the following functions:
Diagnostic tests
Sensor calibrations
Flash programming
Set parametersThe following components are required to use Cat ET to service the engine.
Table 2
Required Electronic Service Tools for the Use of Cat ET    
Part Number    Description    
JERD2124     "Electronic Technician Program" (Cat ET)    
JERD2129     "Data Subscription for All Engines and Machines"    
171-4400 (1)     Communication Adapter II Gp    
( 1 ) The 7X-1700 Communication Adapter Gp may also be used.Note: For more information regarding the use of Cat ET and the PC requirements for Cat ET, refer to the documentation that accompanies your Cat ET software.Connecting Cat ET and the Communication Adapter II
Illustration 1 g00647144
(1) Personal computer (PC) (2) 160-0141 Adapter Cable (PC Serial) (3) 171-4401 Communication Adapter II (4) 207-6845 Adapter Cable (Data Link)Note: Items (2), (3), and (4) are part of the 171-4400 Communication Adapter II Gp .Use the following procedure to connect Cat ET and the communication adapter II.
Turn the keyswitch to the OFF/RESET position. If the keyswitch is not placed in the OFF/RESET position, the engine may start.
Connect cable (2) between the "COMPUTER" end of communication adapter (3) and the RS232 serial port of PC (1) .
Connect cable (4) between the "DATA LINK" end of communication adapter (3) and the service tool connector.
Turn the keyswitch to the ON position. If Cat ET and the communication adapter do not communicate with the ECM, refer to Troubleshooting, "Electronic Service Tool Will Not Communicate With ECM".Optional Service Tools
The following table contains service tools that may be helpful to service the engine, but these tools are not required.
Table 3
Optional Service Tools    
Part Number    Description    
198-4240
or
1U-5470     Engine Pressure Group
Engine Pressure Group    
4C-4075     Crimp Tool (4 To 10 AWG)    
4C-4911 (1)     Battery Load Tester    
5P-7277     Voltage Tester    
6V-9130 (2)     Temperature Adapter (Multimeter)    
8T-5319     Connector Tool Group    
9S-9082     Engine Turning Tool    
( 1 ) Refer to Special Instructions, SEHS9249, "Use of the 4C-4911 Battery Load Tester for 6, 8, and 12 Volt Lead Acid Batteries" and Special Instructions, SEHS7633, "Battery Test Procedure".
( 2 ) Refer to Special Instructions, SEHS8382, "Use of the 6V-9130 Temperature Adapter Group".