811554 Mercruiser OIL SEAL


811554 OIL SEAL Mercruiser 44541101S, 4454110GE, 4454110JT, 4454118JT, 45021102S, 4502111FE, 4542067LS, 4652027LE, 4652027M1, 4652227MW, 474L111JS, 474L118JS, 474L118JT OIL
811554 OIL SEAL Mercruiser
Rating:
78

Buy OIL SEAL 811554 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$25.99
 

30-05-2022
4.8[1.80] Pounds
-: -
The Hillman Group 811554 Hot Dipped Galvanized Hex Bolt, 5/16-Inch x 3-1/2-Inch, 50-Pack
They require a pre-drilled hole with compatible female thread || Hex Bolts feature a six-sided head, which is designed to be tightened using a wrench or drill || Hot Dipped Galavanized || Country of Origin: China
Number on catalog scheme: 3
 

Mercruiser entire parts catalog list:

44541101S 1991,1992,1993,1994,1995,1996
4454110GE 1995
4454110JT 1996,1997
4454118JT 1996,1997
45021102S 1992,1993
4502111FE 1993,1994,1995,1996
4542067LS 1998
4652027LE 1998
4652027M1 1998
4652227MW 1998
474L111JS 1996,1997
474L118JS 1996
474L118JT 1996,1997

Information:


At operating temperature, the engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot water or steam. Any contact can cause severe burns. Look at the sight gauge to check the coolant level. The coolant level should be in the green range. If necessary, remove the fill cap only after the engine has been stopped and the cap is cool enough to remove with your bare hand. Remove the cooling system fill cap slowly to relieve pressure. Cooling system condition contains alkali that can cause personal injury. Avoid contact with the skin and eyes and do not drink. Allow cooling system components to cool before draining.
Put identification on all lines, hoses, wires and tubes for installation purposes. Cap and plug all lines, hoses and tubes to prevent foreign material from entering the system. Drain all fluids in a suitable container for storage or disposal. 1. Drain the engine coolant.2. Loosen bolts (4) and remove water pump drive belt (1).3. Loosen clamp (2) and remove loser radiator hose (3) from the water pump. 4. Loosen clamp (5) and remove the upper hose from the water pump.5. Remove bolts (6) and (7) and remove compressor mounting bracket (8) from the water pump. 6. Disconnect the wire connector from temperature sensor (9).7. Remove bolts (10) and remove the water pump from the engine.End By:a. install right engine guard Refer to the Operation & Maintenance Manual for all fluid capacities and the proper filling procedures.Disassemble & Assemble Water Pump
Start By:a. remove water pump 1. Remove valve assembly (1) and temperature sensor (2) from water pump (4).2. Remove O-ring seals (3). 3. Remove bolts (9) and washers (8) from cover (7).4. Remove cover (7) and gasket (12).5. Remove plug (10) and O-ring seal (11) from cover (7).6. Remove impeller (13) from shaft assembly (17).7. Remove seal assembly (14) from shaft assembly (17).8. Remove shaft assembly (17) from pump housing (15).9. Remove pulley (18) fro shaft assembly (17).10. Remove plug (5) and O-ring seal (6) from pump housing (15).11. Remove filter (16) from pump housing (15). The following steps are for the assembly of the water pump.12. Install filter (16) in pump housing (15). Filter (16) should not extend beyond the surface of the pump housing.13. Install plug (5) and O-ring seal (6).14. Install pulley (18) on shaft assembly (17).15. Install shaft assembly (17) in pump housing (15).
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
16. Install seal assembly (14) over shaft assembly (17) and in pump housing (15).17. Install impeller (13) on shaft assembly (17). Use a feeler gauge to maintain a clearance of 0.75 0.25 mm (.03 .01 in) between impeller (13) and the face surface of pump housing (15).18. Install gasket (12) and cover (7) with bolts (9) and washers (8).19. Install plug (10) and O-ring seal (11).20. Install O-ring seals (3).21. Install valve assembly (1) and temperature sensor (2) in water pump (4).End By:a. install water pump


Parts oil Mercruiser:

72785
 
72785 OIL SEAL, WATER PUMP SHAFT
00014332, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 08986342, 08987343, 228801, 257B021JS, 260801, 30001854, 37011856, 4052110CR, 4211015L1, 4211025RS, 4211025TS, 4211025TT, 4211025U
14957
 
14957 OIL FILTER
01207333, 01402414, 01407333, 01701335, 02602347, 02608427, 04544347, 06661346, 257B021JS, 32001876, 4052110CR, 4111021L1, 4231017L1, 4262C01JT, 430B00001, 430L000JS, 4350100KS, 4350104JS, 4350104KS, 4350111HS, 4350118JS, 4350118KS, 443B0002S, 443B10
821947 1
 
821947 1 OIL SEAL
44541101S, 4454110JT, 4454118JT, 45021102S, 4502111FE, 4542067LS, 4652027LE, 4652027M1, 4652227MW, 474L111JS, 474L118JS, 474L118JT
818743 6
806428T
805561T
821947
850458
OIL PAN
850458 OIL PAN
4454110JT, 4454118JT, 4652027LE, 4652027M1, 4652227MW, 474L111JS, 474L118JT
Back to top