96503 1 Mercruiser SEAL, Oil, DRIVE SHAFT HOUSING - LOWER


96503 1 SEAL, Oil, DRIVE SHAFT HOUSING - LOWER Mercruiser 00019003, 01321017, 01326013, 5000165CE SEAL
96503 1 SEAL, Oil, DRIVE SHAFT HOUSING - LOWER Mercruiser
Rating:
43

Buy SEAL, Oil, DRIVE SHAFT HOUSING - LOWER 96503 1 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Compatible models:

Mercruiser entire parts catalog list:

00019003 1983,1984,1985,1986,1987,1988,1989,1990
01321017 1987
01326013 1983
5000165CE 1990,1991

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B - E12 Torx Socket 1
C 8T-3052 Degree Wheel 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
Inspect the pins of the crankshaft for damage. If the crankshaft is damaged, replace the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove" and Disassembly and Assembly, "Crankshaft - Install" for the correct procedure. Ensure that the bearing shells are clean and free from wear and damage. If necessary, replace the bearing shells.
Illustration 1 g02437999
Install upper bearing shell (5) into connecting rod (3). Ensure that the locating tab for the upper bearing shell is correctly seated in the slot in the connecting rod.Note: The ends of the upper bearing shell must be centered in the connecting rod. The ends of the upper bearing shell must be equally positioned in relation to the mating faces of the connecting rod.
Lubricate upper bearing shell (5) with clean engine oil.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom dead center position.
Carefully pull connecting rod (3) against the crankshaft pin.Note: Do not allow the connecting rod to contact the piston cooling jet.
Clean connecting rod cap (2). Install lower bearing shell (4) into connecting rod cap (2). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Lubricate the pin of the crankshaft and lubricate lower bearing shell (4) with clean engine oil.
Illustration 2 g02437998
Install connecting rod cap (2) to connecting rod (3).Note: Ensure that etched Number (X) on connecting rod cap (2) matches etched Number (X) on connecting rod (3). Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old connecting rod bolts to secure the connecting rod cap.
Install new bolts (1) to the connecting rod. Use Tooling (B) tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts through an additional 120 degrees in a clockwise direction. Use Tooling (B) and Tooling (C) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft to ensure that there is no binding.
Repeat Step 2 through Step 11 for the remaining connecting rod bearings.Note: If all connecting rod bearings require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that both pairs of the connecting rod bearings are installed before changing from one pair of cylinders to another pair of cylinders. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Install" for the correct procedure.
If the glow plugs were removed, install the glow plugs. Ref to Disassembly and Assembly, "Glow Plugs - Remove and Install" for the correct procedure.End By:
If the engine is equipped with a balancer, install the balancer. Refer to Disassembly and Assembly, "Balancer - Install" for the correct procedure.
If the engine is not equipped with a balancer, install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install" for the correct procedure.


Parts seal Mercruiser:

816464 1
 
816464 1 SEAL, Oil, BELL HOUSING
00019003, 01321017, 01326013, 5000150DP, 5000165CE, 5S21800TS
803097T 1
SEAL KIT, Transom (with Exhaust Bellow)
803097T 1 SEAL KIT, Transom (with Exhaust Bellow)
00019003, 01321017, 01326013, 5000165CE
803098T 1
SEAL KIT, Transom (with Exhaust Tube)
803098T 1 SEAL KIT, Transom (with Exhaust Tube)
00019003, 01321017, 01326013, 5000165CE
823894
SEAL, Oil
823894 SEAL, Oil
00019003, 01321017, 01326013, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5S21800TS
65533A 1
SEAL, GIMBAL HOUSING TO TRANSOM
65533A 1 SEAL, GIMBAL HOUSING TO TRANSOM
00019003, 01321017, 01326013, 5000165CE
41607 1
SEAL, Oil, LOWER GIMBAL HOUSING BUSHING
41607 1 SEAL, Oil, LOWER GIMBAL HOUSING BUSHING
00019003, 01321017, 01326013, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5120136JS, 5120150AR, 5120150R1, 5220200AS, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 5C30150FS, 5E31200N1, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS,
12077
 
12077 SEAL
00019003, 01321017, 01326013, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5120150AR, 5220200AS
43713
 
43713 SEAL
5000147JS, 5000150DP, 5000165CE, 5111200LP, 5120136JS, 5120150AR, 5120150R1, 5220200AS, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 5C30150FS, 5E31200N1, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900T
Back to top