804689 Mercruiser SEAT KIT, Inlet


804689 SEAT KIT, Inlet Mercruiser 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 4211015L1, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 4M11025LS, 4M11025RS, 4M11025TS, 4M11025TT, 4M11025US SEAT
804689 SEAT KIT, Inlet Mercruiser
Rating:
8

Buy SEAT KIT, Inlet 804689 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$100.99

31-12-2024

US: A-Partrix
1PCS CV Axle Drive Shaft Assembly CV Joint Front Axle Passenger Right Fits Nissan Maxima 2004 2005 2006 Fits Nissan Altima 2005 2006
a-partrix [Vehicle Fitment]: Right Front Axle Passenger Side Cv Axle Passenger Cv Axle Passenger Side Axle Automotive Constant Velocity Half Shaft Assemblies Fits Nissan Altima 2005 2006 Fits Nissan Maxima 2004 2005 2006 || [Reference Number]: 80-5994, B10338N, 66-6219, 8466N, NI-2154A, 80-4689, CV2275, NCV53612, 93604, 95799, CV3459, 945049, 955275, 7094779, AX-94779, 259202 || [Specifications]: ① Location: Front Right(Passenger Side); ② ABS Ring Tooth Count: 44; ③ABS Ring Type: Toothed; ④Abs Tone Ring Included: Yes; ⑤Number Of Inboard Splines: 26; ⑥Number of Outboard Splines: 29; ⑦Overall Compressed Length (IN): 38.39; ⑧Package Included: 1PCS Front Right Passenger Side CV Axle Shaft || [Easy Installation]: Designed for direct replacement, this CV Axle Shaft assembly features a precise fit and includes all necessary components, ensuring a hassle-free and time-saving installation process. || [Customer Satisfaction Guarantee]: Our CV Axle comes with a 1-Year Unlimited-Mileage Warranty, this CV Axle Shaft is a reliable choice, and we strive to provide you with excellent customer support and a satisfactory shopping experience.
$224.99
 

27-07-2022

-: -
Make Auto Parts Manufacturing Set of 2 Front CV Axle Half Shaft Assembly Driver Left & Passenger Right Side For Nissan Altima & For Maxima 2004 2005 2006 with Automatic Transmission
ITEM FITMENT - For Nissan Altima 2004-2006 & For Nissan Maxima 2004-2006 || WARRANTY - All products are covered by limited Mileage Warranty. || FEATURES - Location - Front, Driver Left & Passenger Right Side / Surface Finish - Painted / Transmission Type - Automatic / Compressed Length - 24 11/16" (Driver Side), 38 15/32" (Passenger Side) / Inner Spline - 26 / Outer Spline - 29 / ABS on Axle - 44T || NOTES - Interchange Part Number - 60-6218 80-4688 60-6219 80-4689, 606218 804688 606219 804689 || FREE SHIPPING - Add to your cart NOW
$46.24

25-12-2024
0.9038[0.41] pounds
LU: Amazon Global Store
Valeo 804689 Cylinder transmitter, clutch
Valeo
Number on catalog scheme: 14
 

Mercruiser entire parts catalog list:

4111021L1 1998
4111021TS 1998
4111021UT 1998
4111021UU 1998
411102KN2 1998
4211015L1 1998
4211025RS 1998
4211025TS 1998
4211025TT 1998
4211025US 1998
4211025UU 1998
4M11025LS 1998
4M11025RS 1998
4M11025TS 1998
4M11025TT 1998
4M11025US 1998

Information:


Table 1
Diagnostic Codes Table
Code Conditions which Generate this Code System Response
2417-5 Ether Injection Control Solenoid : Current Below Normal The Electronic Control Module (ECM) detects low current in the circuit. The code is latched. The code is logged.
Ether injection is disabled.
2417-6 Ether Injection Control Solenoid : Current Above Normal The ECM detects excessive current flow in the circuit. The ether injection system improves cold weather starting of the engine. The ECM controls the ether injection system. The ether injection system is enabled when all of the following conditions occur:
The configuration parameter is enabled or the configuration parameter is set to continuous flow.
The intake manifold air temperature is less than 0 °C (32 °F) or the engine coolant temperature is less than 0 °C (32 °F).
Engine speed is greater than 0 rpm and less than 50 rpm below the low idle speed.
No diagnostic codes are active for both the engine coolant temperature sensor and for the intake manifold air temperature sensor.
Illustration 1 g02099717
Schematic of the ether injection system
Illustration 2 g02099721
P1 terminals for the ether injection system
(P1-10) Starting aid solenoid
(P1-18) Return for the starting aid solenoid
Illustration 3 g01155187
Terminal locations at the harness connector for the ether solenoid
(1) Starting aid solenoid
(2) Return for the starting aid solenoid
Table 2
Troubleshooting Test Steps Values Results
1. Check the Harness Connectors
A. Verify that the keyswitch is in the OFF position.
B. Disconnect the harness connector for the ether solenoid.
C. Check the harness connector for debris and for corrosion.
Connectors
Result: The harness connector was not free of debris and/or not free of corrosion.
Repair: Perform the following procedure:
1. Clean the harness connector.
2. Reconnect the harness connector. Verify that the connection is secure.
3. Verify that the problem is resolved.
If the problem is not resolved, proceed to Test Step 2.
Result: The harness connector was free of debris and free of corrosion.
Proceed to Test Step 2.
2. Create an Open at the Harness Connector for the Ether Injection Solenoid
Note: The ether canister must be removed prior to performing this procedure.
A. If necessary, disconnect the harness connector from the ether solenoid.
B. Turn the keyswitch to the ON position.
C. A test on Caterpillar Electronic Technician (ET) allows the technician to activate the ether system. The test can be activated by selecting the "Diagnostic Overrides" screen on Cat ET.
D. Activate the ether injection system. The system will activate for 10 seconds.
E. Measure the voltage across terminal 1 and terminal 2 of the harness for the ether injection solenoid.
F. Turn the keyswitch to the OFF position.
Voltage
Result: The voltage measurement is 0 VDC after activating the ether injection system.
Repair: There is a problem in the harness. Repair the harness or replace the harness.
Verify that the problem is resolved.
STOP
Result: The voltage measurement is equal to battery voltage after activating the ether injection system.
Repair: There is a problem in the solenoid. Replace the solenoid.
Verify that the problem is resolved.
STOP
Test Step 1. The procedure corrected the issue. Return to service.Results:
The procedure did not correct the issue. - Repair: Contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).STOP


Back to top