863187A 2 Mercruiser SENDER ASSEMBLY, Trim


863187A 2 SENDER ASSEMBLY, Trim Mercruiser 5E31200N1, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900TS, 5E31910TP, 5E31910TS, 5E32200TP, 5E32900TS, 5E36200TP, 5E36200TS, 5E36210TP, 5E36210TS, 5E36800TP, 5E36800TS, 5E36810TP, 5E36810T SENDER
863187A 2 SENDER ASSEMBLY, Trim Mercruiser
Rating:
38

Buy SENDER ASSEMBLY, Trim 863187A 2 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 25
 

Mercruiser entire parts catalog list:

5E31200N1 1998
5E31200TP 1998
5E31200TS 1998
5E31210TP 1998
5E31210TS 1998
5E31800TP 1998
5E31800TS 1998
5E31810TP 1998
5E31810TS 1998
5E31900TP 1998
5E31900TS 1998
5E31910TP 1998
5E31910TS 1998
5E32200TP 1998
5E32900TS 1998
5E36200TP 1998
5E36200TS 1998
5E36210TP 1998
5E36210TS 1998
5E36800TP 1998
5E36800TS 1998
5E36810TP 1998
5E36810TS 1998
5E36900TS 1998
5E36910TP 1998
5E36910TS 1998
5H41400TP 1998
5H41410TP 1998
5H41410TS 1998
5H41600TP 1998
5H41610TP 1998
5H41610TS 1998
5H42300TP 1998
5H42300TS 1998
5H42400TS 1998
5M41400TP 1998
5M41400TS 1998
5M42300TP 1998
5M42300TS 1998
5T32300TP 1998
5T32300TS 1998
5X32200TS 1998
6511102N1 1998

Information:

Probable Causes
Diagnostic codes
Event codes
Derates
Engine parameters
Throttle signal
Air inlet and exhaust system
Fuel supply
Cylinder performanceRecommended Actions
Diagnostic Codes, Event Codes and Derates
Certain diagnostic codes, event codes and/or derates may cause poor performance. Connect Caterpillar Electronic Technician (ET) and check for active codes and/or for logged codes. Troubleshoot any codes that are present before continuing with this procedure.If this application supports engine derates, use Cat ET to check for logged derates. Refer to Troubleshooting, "Event Code List" for the specific events that are applicable to this application. A status screen on Cat ET will display a derate if a derate is active.Engine Parameters
Verify that the correct engine parameters are being used.Throttle Signal
Monitor the status for "Throttle Position" on Cat ET. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed.Air Inlet and Exhaust System
Check the air filter restriction indicator, if equipped. Clean plugged air filters or replace plugged air filters. Refer to the Operation and Maintenance Manual.
Check the air inlet and exhaust system for restrictions and/or leaks. Refer to Systems Operation/Testing and Adjusting.Fuel Supply
Visually check the fuel level. Do not rely on the fuel gauge only. If necessary, add fuel. If the engine has been run out of fuel, it will be necessary to purge the air from the fuel system. Refer to Operation and Maintenance Manual.
Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
Check the fuel lines for the following problems: restrictions, collapsed lines, pinched lines and loose connections. If problems are found with the fuel lines, repair the lines and/or replace the lines.
Prime the fuel system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuit
Replacement of unit injectorsNote: A sight glass in the low pressure supply line is helpful in diagnosing air in the fuel. Refer to Systems Operation/Testing and Adjusting.
Check the fuel tank for foreign objects which may block the fuel supply.
Check the fuel filters.
Check the diesel fuel for contamination. Refer to Systems Operation/Testing and Adjusting.
Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.Cylinder Performance
Check the valve lash and reset the valve lash, if necessary. Refer to Systems Operation/Testing and Adjusting for the procedure.
Check for correct installation of the unit injector connectors. Check for correct installation of all other applicable connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
Perform the "Cylinder Cutout Test" on Cat ET in order to identify any injectors that might be misfiring.
If Cat ET indicates a problem, remove the electronic unit injector from the suspect cylinder. Refer to Disassembly and Assembly.
Possible causes of low compression are shown in the following list:
Faulty piston
Faulty piston rings
Worn cylinder bores
Worn valves
Faulty cylinder head gasket
Damaged cylinder head
Perform all necessary repairs. Ensure that the repairs have eliminated the problem.


Parts sender Mercruiser:

805130A 6
SENDER KIT, Dual Station (BLACK)
805130A 6 SENDER KIT, Dual Station (BLACK)
00019003, 01321017, 01326013, 5000165CE, 5120136JS, 5120150R1, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 5C30150FS, 5E31200N1, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900TS, 5E31910TP,
Back to top