95854A 3 Mercruiser SHIFT LEVER ASSEMBLY


95854A 3 SHIFT LEVER ASSEMBLY Mercruiser 00014332, 01851333, 01854335, 02287333, 02607333, 02608427, 04544347, 04707333, 04708004, 04881333, 06661346, 07711346, 08987343, 30001854, 32001876 SHIFT

Buy SHIFT LEVER ASSEMBLY 95854A 3 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

Mercruiser entire parts catalog list:

00014332 1982
01851333 1983,1984
01854335 1985,1986
02287333 1983
02607333 1983
02608427 1987
04544347 1987
04707333 1983
04708004 1984
04881333 1983
06661346 1986,1987,1988,1989
07711346 1986,1987
08987343 1983,1984,1985,1986,1987
30001854 1984,1986
32001876 1986,1987

Information:


Table 1
Diagnostic Trouble Codes for DEF Tank Level Is Low
J1939 Code Code Description Comments
1761-1 Aftertreatment #1 DEF Tank Volume #1 : Low - most severe (3) This code is a Level 3 inducement that becomes active when the DEF tank is empty. The engine is derated 100%, limited to low idle or 1000 RPM, and may experience 5 minute rolling shutdowns.
1761-17 Aftertreatment #1 DEF Tank Volume #1 : Low - least severe (1) This code is a Level 1 inducement that becomes active when the DEF level is critically low.
1761-18 Aftertreatment #1 DEF Tank Volume #1 : Low - moderate severity (2) This code is a Level 2 inducement that becomes active when the DEF level is critically low. Power loss may occur.
Follow the troubleshooting procedure to identify the root cause of the problem. Note: If active 1761 diagnostic codes are present, this may be due to an issue with the DEF pump which is causing a loss of prime. Operate the machine for several minutes and check to see if the DEF levels recover.Refer to Systems Operation, Testing and Adjusting, "DEF Dosing Control System" for details on inducement configuration options and inducement actions for specific tank levels.Note: Always turn the keyswitch to the OFF position before adding DEF to the tank.Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Check the DEF Level
A. Clean dirt and debris from around the cap before removing the cap.
B. Visually check the DEF level in the tank. If the DEF level is greater than 75%, proceed to Test Step 2. If the DEF level is less than 75%, continue with this procedure.
C. Turn the keyswitch to the ON position. Do not start the engine.
D. Wait for at least 1 minute. Check the current position of the DEF gauge.
E. Turn the keyswitch to the OFF position.
F. Clean dirt and debris from around the cap before removing the cap.
G. Fill the DEF tank to at least 25% capacity.
Note: Only use DEF that meets ISO 22241 quality standards.
H. Turn the keyswitch to the ON position.
I. Check for a change in the gauge position.
Gauge position
Result: The gauge did not move when DEF was added to the tank.
Proceed to Test Step 2.
Result: The gauge moved when DEF was added to the tank. Turn the keyswitch to the OFF position for 2 minutes to allow the DEF pump to purge, reset the code, and reset the Electronic Control Module (ECM).
Return the unit to service.
2. Check the Electrical Connection for the DEF Tank Header
A. Inspect the electrical connector to the DEF tank header. Refer to Troubleshooting, "Electrical Connectors - Inspect" for further information.
Look for corrosion or loose wires.
Electrical connections
Result: The electrical connectors are free of corrosion and are not loose.
Proceed to Test Step 3.
Result: The electrical connections are not free of corrosion and/or are loose.
Repair: Make the necessary repairs to the connectors. Turn the keyswitch to the OFF position for 2 minutes to allow the DEF pump to purge, reset the code, and reset the ECM.
Repeat the procedure from Test Step 1.
3. Inspect the DEF Tank Header
A. Turn the keyswitch to the OFF position.
B. Remove the DEF tank header (2) from the DEF tank. Refer to Disassembly and Assembly, "Manifold (DEF Heater) - Remove and Install".
C. If necessary, remove the filter sock from the DEF tank header.
D. Inspect the DEF tank header for a stuck float.
Correct operation of the float
Result: The float was not operating correctly.
Repair: If possible, repair the float and then install the filter sock. If the float cannot be repaired, replace the DEF tank header. Refer to Disassembly and Assembly, "Manifold (DEF Heater) - Remove and Install".
Return the unit to service.
Result: The float was operating correctly.
Repair: Install a replacement DEF tank header. Refer to Disassembly and Assembly, "Manifold (DEF Heater) - Remove and Install".
If the fault is still present, contact the Dealer Solutions Network (DSN).


Parts shift Mercruiser:

66057A 3
 
66057A 3 SHIFT BRACKET ASSEMBLY
00014332, 02287333, 02607333, 08986342, 2140208, 2165208, 2250507, 228801, 260801, 2888203
76865
 
76865 SHIFT CRANK
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 2250507, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5220200AS, 5S21800TS, 91331015
19755A 2
 
19755A 2 SHIFT SPOOL KIT
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 5000150DP, 5000165CE
94912A3
 
94912A3 SHIFT PLATE ASSEMBLY
02287333, 02607333, 228801, 260801
98301A 3
 
98301A 3 SHIFT CRANK ASSEMBLY
03307332, 03308333, 04544347, 30001854, 37011856, 44031854
98299A 2
 
98299A 2 SHIFT ROD ASSEMBLY
03307332, 03308333, 04544347, 30001854, 37011856, 44031854
99237A10
 
99237A10 SHIFT BRACKET ASSEMBLY
00014332, 01207333, 01402414, 01407333, 01701335, 01751347, 01854335, 02287333, 02602347, 02607333, 02608427, 04544347, 06661346, 07711346, 08987343, 257B021JS, 4052110CR, 4350104JS, 4350111HS, 4350118JS, 443B0002S, 443B1003S, 44541101S, 4454110AS, 4
13898A 3
 
13898A 3 SHIFT LEVER ASSEMBLY
00014332, 01207333, 01402414, 01407333, 01701335, 01751347, 01854335, 02287333, 02602347, 02607333, 02608427, 04544347, 06661346, 07711346, 08987343, 257B021JS, 4111021L1, 411102KN2, 4211015L1, 4211025RS, 4231017L1, 4262C01JT, 430B00001, 430L000JS, 4
Back to top