45600 Mercruiser SLEEVE, SWITCH ACTUATING STUD


45600 SLEEVE, SWITCH ACTUATING STUD Mercruiser 00014332, 01207333, 01402414, 01407333, 01701335, 01851333, 01854335, 02287333, 02607333, 02608427, 04544347, 04707333, 04708004, 04881333, 06661346, 07711346, 08986342, 08987343, 2140208, 2165208, 2250507, 228801, 260801, 2888203, 30001854, 32001876 SLEEVE

Buy SLEEVE, SWITCH ACTUATING STUD 45600 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

Mercruiser entire parts catalog list:

00014332 1982
01207333 1983
01402414 1984,1985,1986,1987,1988,1989
01407333 1983
01701335 1985,1986,1987,1988,1989
01851333 1983,1984
01854335 1985,1986
02287333 1983
02607333 1983
02608427 1987
04544347 1987
04707333 1983
04708004 1984
04881333 1983
06661346 1986,1987,1988,1989
07711346 1986,1987
08986342 1982,1983
08987343 1983,1984,1985,1986,1987
2140208 1978,1979,1980,1981,1982
2165208 1978
2250507 1977
228801 1981,1982
260801 1981,1982,1987
2888203 1973,1974,1975,1976,1977
30001854 1984,1986
32001876 1986,1987

Information:


For initial start-up of a new or rebuilt engine, and for start-up of an engine that has been serviced, make provision to shut the engine off should an overspeed occur. This may be accomplished by shutting off the fuel supply and/or the ignition to the engine.
Note: Using the "EMERGENCY STOP" button will shut off both the fuel and the ignition.Do not start the engine or move any of the controls if a "DO NOT OPERATE" tag is attached to the start switch or controls. Do not start the engine or move any of the controls if there is a similar warning tag attached to the start switch or controls.Ensure that no one will be endangered before the engine is started and when the engine is started.Perform the procedures that are described in this Operation and Maintenance Manual, "Before Starting Engine" (Operation Section).Purging Unburned Gas
Unburned gas in the air inlet and exhaust system may ignite when the engine is started. Personal injury and/or property damage may result.Before starting an engine that may contain unburned gas, purge the unburned gas from the air inlet and exhaust system. Refer to the topic on purging unburned gas in the "Starting the Engine" section.
The following events cause unburned gas to remain in the air inlet and in the exhaust manifold:
Emergency stop
Engine overspeed
The engine control is set to the STOP mode and the gas shutoff valve does not close.
Unsuccessful successive attempts to start the engineUnburned gas may remain in the air inlet and exhaust system after several unsuccessful attempts to start the engine. The unburned gas may increase to a concentration that may ignite during a successive attempt to start the engine.Perform the following procedure in order to purge the unburned gas:
If the Cat Electronic Technician (ET) is not connected to the engine, connect Cat ET to the engine.
Verify that the value of the "Engine Purge Cycle" parameter is equal to 10 seconds less than the value of the "Crank Cycle" parameter.
Set the engine control to the START mode. The engine will crank for the "Engine Purge Cycle" time. Then, the gas shutoff valve will be energized and the ignition will be enabled. The engine will start.
Continue with your previous procedure. Automatic Starting
When the engine is in the AUTOMATIC mode, the engine can start at any moment. To avoid personal injury, always remain clear of the the engine when the engine is in the AUTOMATIC mode.
If the engine control switch is in the "AUTO" position, the engine will automatically start when the remote start/stop initiate contact closes.Parameters for the Start/Stop Control
Driven Equipment
Start-up is delayed until the switch for the driven equipment indicates that the driven equipment is ready.Purge Cycle
Note: The engine uses an energize-to-run system. The gas shutoff valve must remain energized in order to supply fuel to the engine.The purge cycle allows any unburned fuel to exit through the exhaust before the engine is allowed to fire.The purge cycle occurs under these conditions:
The gas shutoff valve is de-energized.
The ignition is off.
The engine is cranked.The purge cycle occurs before the crank cycle. The amount of time for the purge cycle is programmable.Cycle Crank Time
The maximum amount of time for activation of the starting motor and the gas shutoff valve for starting is the cycle crank time. The amount of time is programmable. The cycle crank time is only active for automatic starting.Rest Cycle
If the engine does not start within the cycle crank time, starting is suspended for a rest cycle. The amount of time for the rest cycle is equal to the cycle crank time. The overcrank time is only active for automatic starting.Overcrank Time
The overcrank time includes the total purge cycle, the total cycle crank time, and the total rest cycle. These functions are repeated until termination of the overcrank time.If the engine does not start within the overcrank time, the engine control module generates an event code.


Parts sleeve Mercruiser:

57908 2
 
57908 2 SLEEVE, WIRING HARNESS
01206002, 01207333, 01326013, 01851333, 02287333, 02607333, 2165203, 2165208, 228801, 260801
60096
 
60096 SLEEVE, TERMINAL END COVER
01206002, 01207333, 01326013, 01406002, 01407333
60775
 
60775 SLEEVE, SPACER
01206002, 01207333, 01326013, 01406002, 01407333, 04706002, 04707333
21309
72119
 
72119 SLEEVE, WATER
01701335, 04706002, 04707333, 04708004, 04856332, 04881333
Back to top