813312 Mercruiser SNAP RING


813312 SNAP RING Mercruiser 428B116KD, 442B110GD, 442B115KD, 4A72040ND SNAP
813312 SNAP RING Mercruiser
Rating:
38

Buy SNAP RING 813312 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$18.29

24-11-2024
0.47[0.21] Pounds
US: Race-Driven Inc
CV Boot Kit fits Honda Foreman Rubicon 500 TRX500FM 4x4 2015-2019 Rear Outer
Race-Driven Heavy Duty CV Boot || High quality rubber for extended life kit includes grease and clamps. || Replace those cracked or punctured boots before dirt and water ruin your CV shaft. || Fits: 2015 2016 Honda Foreman Rubicon 500FM5 4x4, 2015 2016 2017 2018 2019 Honda Foreman Rubicon 500FM6 4x4 EPS, 2015 2016 Honda Foreman Rubicon 500FM7 4x4 EPS DLX
$169.80
 

07-10-2017
12.00[5.40] pounds
Motoworks: Motoworks
Motoworks EZ-FIT Nerf Bars - Black 81-3312
Custom EZ-fit clamp brackets with silver anodized finish||Wide 11/2in black webbing with beefy aluminum net tabs||Replacement webbing available in red, blue and black||Manufactured from lightweight 11/4in extruded aluminum tubing||Sweep up from front to the rear for maximum ground clearance
$31.21
 

07-10-2017

Needa Part: Needa Parts
Needa Parts 813312 Front/Rear Left/Right Black Exterior Door Handle
Meets or exceeds OEM standards||Outside Door Handle||Finish: Paint To Match
Number on catalog scheme: 34
 

Compatible models:

Information:

2. Loosen clamp (1).3. Remove two bolts (2).4. Remove two bolts (3) and washers.5. Remove water pump (4) and the gasket. When installing replace the gasket. Make sure all gasket surfaces are clean and free of dirt. For installation of the water pump, reverse the removal steps.6. Fill the radiator with coolant to the proper level. See the Operation & Maintenance Manual.Disassemble & Assemble Water Pump
The following tools are needed for disassembly. Start By:a. remove water pump 1. Remove bolt (15) and the washer. Remove bearing (12) and gear (10) as a unit.2. Use Tool (A), (C) and a press, and remove bearing (12) from gear (10).3. Remove snap ring (8) with Tool (B).4. Remove two bolts (1), the washers, cover (14) and gasket (2) from water pump housing (18).5. Loosen bolt (13) approximately 6.4 mm (.25 in). Hit the bolt with a soft hammer to loosen impeller (16) from shaft (9).6. Remove bolt (13), washer (11), impeller (16), spring (3) and seal assembly (4) from shaft (9).7. Remove bearing (7) and shaft (9) as a unit.8. Use Tool (A), (C) and a press to remove bearing (7) from shaft (9).9. Remove ceramic seal (5) and seal (17) from water pump housing (18).10. Use Tool (C) to remove lip-type seal (6) from the water pump housing. The following steps are for assembly of the water pump. The following tools are needed for assembly. 11. Install lip-type seal (6) in water pump housing (18) with Tool (C). The lip of the seal must be toward the bearings. Put clean engine oil on the lip of the seal.12. Install shaft (9) in bearing (7) with a press.13. Install shaft (9) and bearing (7) as a unit in water pump housing (18).14. Install snap ring (8) with Tool (B).
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
15. Put ceramic ring (5) in position in seal (17). Use hand pressure and Tool (D) to install the ceramic ring.16. Remove spring (3) from seal assembly (4). Use hand pressure and Tool (D) to install the seal assembly. Push seal assembly (4) on shaft (9) until it makes light contact with ceramic ring (5).17. Install spring (3) on seal assembly (4). Put impeller (16) in position on shaft (9), and install washer (11) and bolt (13) that hold it. Tighten bolt (13) to a torque of 38.0 1.5 N m (28 1 lb ft).18. Put gasket (2) and cover (14) in position on water pump housing (18). Install the two washers and bolts (1) that hold them.19. Install bearing (12) on gear (10) with a press.20. Position gear (10) and bearing (12) as a unit on shaft (9). Install the washer and bolt (15) that hold them together. Tighten bolt (15) to a torque of 97 7 N m (72 5 lb ft).End By:a. install water pump


Parts snap Mercruiser:

93914
 
93914 SNAP RING, BALL HEARING
00014332, 01207333, 01402414, 01407333, 02287333, 02602347, 02607333, 02608427, 08986342, 08987343, 228801, 257B021JS, 260801, 40280002D, 40420001D, 40420002D, 40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4211025RS, 4211025TS, 4211025TT, 42
93915
 
93915 SNAP RING, INPUT SHAFT
00014332, 01207333, 01402414, 01407333, 02287333, 02602347, 02607333, 02608427, 08986342, 08987343, 228801, 257B021JS, 260801, 40280002D, 40420001D, 40420002D, 40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4211025RS, 4211025TS, 4211025TT, 42
94104
 
94104 SNAP RING, BALL BEARING, INTERNAL
00014332, 01207333, 01402414, 01407333, 02287333, 02602347, 02607333, 02608427, 08986342, 08987343, 228801, 257B021JS, 260801, 40280002D, 40420001D, 40420002D, 40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4211025RS, 4211025TS, 4211025TT, 42
813321
 
813321 SNAP RING
428B116KD, 442B110GD, 442B115KD, 4A72040ND
809934175
 
809934175 SNAP RING
40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
Back to top