5010184GP Mercruiser STERNDRIVE, (1.84)


5010184GP STERNDRIVE, (1.84) Mercruiser 5000150DP, 5000165CE STERNDRIVE
5010184GP STERNDRIVE, (1.84) Mercruiser
Rating:
58

Buy STERNDRIVE, (1.84) 5010184GP Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$264.99
 

12-05-2024

US: The ROP Shop
The ROP Shop | Trim Cylinder Ram Set for 1994 Mercruiser ALPHA [1.84:1] 5010184GS, 5010184GP
The ROP Shop The ROP Shop replacement Trim Cylinder Ram Set for 1994 Mercruiser ALPHA [1.84:1] 5010184GS, 5010184GP || Specs - Refer to images 2 & 3 for more information || Includes - (1) Trim Cylinder Ram Set; comes as shown in the first image || Fits/For Gen II (Port) S/N 0F680000-UP || Please be sure to check your part or model number to ensure this is the correct Trim Cylinder Ram for your unit. Also, please note this may replace multiple part numbers
$39.99
 

12-05-2024

US: The ROP Shop
The ROP Shop | Trim Line Manifold Assembly for 1994 MerCruiser 5010150GS, 5010184GP, 5010198GS
The ROP Shop The ROP Shop replacement Trim Line Manifold Assembly for 1994 MerCruiser 5010150GS, 5010184GP, 5010198GS || Specs - Refer to images 2 & 3 for more information || Includes - (1) Manifold, (2) Gaskets, (1) Spacer, (2) Bolts & (2) Tooth Lock Washers; comes as shown in the first image || Fits/For: 1983 and newer Alpha & Bravo drives. Manifold mounts under the outdrive for your power trim/tilt hoses || Please be sure to check your part or model number to ensure this is the correct manifold assembly for your unit. Also, please note this may replace multiple part numbers
$44.99
 

18-05-2022

-: -
The ROP Shop | Lower Shift Cable Assembly for 1994 Mercruiser 5010198GS, 5010184GP Boat Engines
The ROP Shop replacement Lower Shift Cable Assembly for 1994 Mercruiser 5010198GS, 5010184GP Boat Engines || Specs - Conduit: 63". Refer to images 2 & 3 for more information || Includes - (1) Shift Cable Assembly with Slide, Screws, Guide Anchor, Wrapping & Insert; comes as shown in the first image || This cable is built for long life and maximum performance in all weather conditions to below zero Fahrenheit. It employs layered technology structure to create a smooth operating & durable control cable || Has old style stranded core wire with soldered tip (uses support tube)
Number on catalog scheme: -
 

Compatible models:

5000150DP   5000165CE   Mercruiser

Mercruiser entire parts catalog list:

5000150DP 1991,1992,1993,1994,1995
5000165CE 1990,1991

Information:

1. Remove the two bolts and lock to remove suction bell assembly (1) from the oil pump. 2. Remove the two bolts that hold elbow (3) to the oil pump.3. Remove bolts (2), the locks, bolts (4) and remove the oil pump. The weight of the oil pump is 35 lb. (16 kg).Install Oil Pump
1. Turn the crankshaft until the No. 1 piston is at the top center compression position. See INSTALL FUEL INJECTION PUMP HOUSING AND GOVERNOR. 2. Turn both balancer shafts until the flat part on each shaft is away from the oil pan plate. Install two 3/8"-16 NC bolts (1) 1 1/2" long through the oil pan plate and into the holes in the balancer shafts. This will make the shafts so they will not turn. Do not tighten the bolts against the bottom of the holes in the shafts.3. Put the oil pump in position on the engine block and install the locks (left side only) and bolts that hold the oil pump in place. Surface (2) of the oil pump must be free of lock tabs.4. Remove bolts (1). Check to see that the balancer shaft timing is correct. The balancer shaft timing is correct when the holes in the balancer shafts are in alignment with the holes in the oil pan plate, and No. 1 piston is at the top center compression position.5. Make sure the gasket is in position and install the bolts that hold elbow (3) to the oil pump.6. Put the gasket and suction bell assembly (4) in position and install the bolts and lock to hold it.end by:a) install oil panDisassemble Oil Pump
start by:a) remove oil pump
TYPICAL EXAMPLE1. Remove idler gear (2).2. Remove bearing (1) from gear (2) with tooling (B).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (C). OIL PUMP Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (A) as follows: a) Put bearings (1) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is .060 in. (1.52 mm) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.2. Install the bearings in oil pump body assembly with tooling (A) as follows: a) Put bearings (2) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump body. Make sure the joints in the bearings are at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See OIL PUMP (2P1785) in SPECIFICATIONS.4. Put clean engine on all of the parts of the oil pump. 5. Install pressure relief valve (3), cover (4) and bolt (5) in the oil pump body assembly.6. Install gears and shafts (6) in the oil pump body assembly. 7. Install spacer (7) and the two keys in shafts (6). 8. Install two gears and scavenge pump body assembly (8).9. Install key (9), drive gear (11), the washer and bolt (10). Tighten the bolt to a torque of 32 5 lb.ft. (43.4 6.8 N m).10. Install the bearing in the idler gear with tooling (B) until it is even with the outside surface of the gear.11. Install the idler gear.
The oil pump must turn freely by hand after it is assembled.
end by:a) install oil pump


Back to top