5K32300TP Mercruiser STERNDRIVE, Bravo-II X Diesel (1.65:1)


5K32300TP STERNDRIVE, Bravo-II X Diesel (1.65:1) Mercruiser 5232100TP, 6311002NZ, 6315002NZ, 6811001N1 STERNDRIVE
5K32300TP STERNDRIVE, Bravo-II X Diesel (1.65:1) Mercruiser
Rating:
73

Buy STERNDRIVE, Bravo-II X Diesel (1.65:1) 5K32300TP Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$89.99
 

24-10-2023

-: -
The ROP Shop | Spanner & Bearing Carrier Tool for 1998 MerCruiser Bravo 2X 5K32241TS, 5K32300TP
The ROP Shop replacement Spanner & Bearing Carrier Tool for 1998 MerCruiser Bravo 2X 5K32241TS, 5K32300TP || Specs - Refer to images 2 & 3 for more information || Includes - (1) Bearing Carrier Retainer Wrench & (1) Spanner Nut Wrench; comes as shown in the first image || Fits/For: Bravo One and Two, MC-I, R-MR, Alpha One, Alpha One Gen II, TRS drive units and outboards || Removes and installs bearing carrier retainer nut and spanner nut. Please be sure to check your part or model number to ensure this is the correct tool set for your unit. Also, please note this may replace multiple part numbers
$43.99
 

03-10-2023

-: -
The ROP Shop | Steering Shaft Pin for 1998 MerCruiser Bravo 2X 5K32231TS, 5K32241TS, 5K32300TP
The ROP Shop replacement Steering Shaft Pin for 1998 MerCruiser Bravo 2X 5K32231TS, 5K32241TS, 5K32300TP || Specs - Overall Shaft Length: 4 1/2". Shaft Material: 304 stainless steel. Refer to images 2 & 3 for more information || Includes - (1) Shaft Pin, (1) Seal, (1) Lock Nut, (2) Bushings & (2) Washers; comes as shown in the first image || Fits/For MerCruiser Alpha One, Gen II, Bravo I, II, III, & Vazer sterndrives || Please be sure to check your part or model number to ensure this is the correct gimbal steering shaft pin kit for your unit. Also, please note this may replace multiple part numbers
$39.99
 

11-06-2023

-: -
The ROP Shop | Trim Sender Limit for 1998 MerCruiser Bravo 2X 5K32300TP, 5K32300TS, 5K32400TP
The ROP Shop replacement Trim Sender Limit for 1998 MerCruiser Bravo 2X 5K32300TP, 5K32300TS, 5K32400TP || Specs - Refer to images 2 & 3 for more information || Includes - (1) Trim Limit Switch with Wire Leads & (1) Trim Sender Switch with Wire Leads; comes as shown in the first image || Fits/For: MerCruiser MC-I, R, MR, Alpha One, Gen II and Bravo drives || Please be sure to check your part or model number to ensure this is the correct sender limit kit for your unit. Also, please note this may replace multiple part numbers
Number on catalog scheme: NS
 

Compatible models:

Mercruiser entire parts catalog list:

Information:

Introduction
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.If the crankshaft, gear case and/or crank gear are replaced, it is necessary to calibrate the injection timing. The following steps show how to calculate/determine the new injection timing by measuring angular deviation between the crankshaft TDC and Crank Position sensor detected TDC.Note: Once complete the engine ecm must be reprogrammed with the new injection timing value.Follow all steps.Procedure
Illustration 1 g06220548
(1) TC Mark (Flywheel Housing)
(2) TC Mark (Flywheel)
Remove valve cover, and injector and rocker arm. Bring the piston of cylinder 4 to TDC.
Illustration 2 g06220554
(3) Dial Gauge
(4) Valve
(5) O-ring
Remove the #4 exhaust valve bridge arm and valve spring. Insert a small O-ring (5) so the valve does not fall into the cylinder.
Set dial gauge (3) on the tip of the valve (4).
Illustration 3 g06220569
(6) Tri - Square
(7) Flywheel Housing
(8) Flywheel
Illustration 4 g06220573
(7) Flywheel Housing
(8) Flywheel
(9) Reference Line
Turn the flywheel counterclockwise and measure the position where the tip of the valve is the highest.
Stop the flywheel at the position where the tip of the valve is the highest. Put a tri - square (6) on the flywheel housing (7) and the flywheel (8) and draw a reference line (9).Do not drop the valve (4) into the cylinder. When measuring the highest position of the tip of the valve, do not rotate the flywheel clockwise. If you go past the highest point of the valve, back up the flywheel slightly and measure the highest point of the valve. The reference line (9) indicates the TDC of the crankshaft.
Illustration 5 g06220579
Rotation Sensor Signal Interface Unit
Application: Use for reading rotation sensor signal.
(1) 9V Battery
(2) Switch
(3) 3-Terminal Regulator
(4) LED
(5) Clip (Red)
(6) Clip (Black)
(A) for Panasonic
(B) for Denso
(C) for Bosch cam angle
(D) for Bosch crank angle
((E)) Connector Side
(a) +9 V
(b) Signal
(c) GND
(d) +5 V
(e) Signal
(f) GND
Schematic to build Rotation Sensor Signal Interface.
Illustration 6 g06220581
(10) Rotation Sensor Signal Interface (Tool not available. Schematic to build tool available. Refer to Step 6.
(11) Tester
Illustration 7 g06220587
(12) Ground Terminal
(13) Output Terminal
(14) Crankshaft Position Sensor
Connect a connector of the rotation sensor signal interface unit (10) to the crankshaft position sensor (14). Connect each clip of the rotation sensor signal interface unit (10) to the same test lead color of the tester (11). Switch on the rotation sensor signal interface unit (10).
Illustration 8 g06220590
(15) Pulsar Gear
(16) 14th Tooth
(17) Missing Teeth
Turn the flywheel and make sure that the voltage of the crankshaft position sensor goes from 0→ 5 V or 5 → 0 V.
Rotate the flywheel and align the crankshaft position sensor to the part of the pulsar gear (15) that is missing teeth (17). The 14th tooth (16) from the missing teeth is standard.
Slowly turn flywheel counterclockwise and stop flywheel at the point where needle of the tester changes momentarily from 0 → 5 V, the 14th tooth.That point is where the crankshaft position sensor detects TDC.
Illustration 9 g06220608
(18) Crankshaft TDC
(19) Detection Point of Crankshaft Position Sensor TDC
Illustration 10 g06220612
(20) Interval
Set the tri - square (6) on the reference line (9) on the flywheel housing side and mark the detection point of crankshaft position sensor TDC (19) on the flywheel.
Measure the interval (20) between the crankshaft TDC (18)


Parts sterndrive Mercruiser:

5C31100LP
STERNDRIVE UNIT COMPLETE (1.36:1 Ratio)
5C31100LP STERNDRIVE UNIT COMPLETE (1.36:1 Ratio)
5120136JS, 5120150R1, 5231100LP, 6020006JS, 6211001N1, 6311002NZ, 6315001N1, 6315002NZ, 6416003N2, 6511102N1, 6811001N1
5231100NP
STERNDRIVE UNIT (Complete)
5231100NP STERNDRIVE UNIT (Complete)
5120150R1, 5231100LP, 6211001N1, 6311002NZ, 6315001N1, 6811001N1
5231200NP
STERNDRIVE UNIT (Complete)
5231200NP STERNDRIVE UNIT (Complete)
5120150R1, 5231100LP, 6211001N1, 6311002NZ, 6315001N1, 6811001N1
5447600NP
STERNDRIVE UNIT, Complete
5447600NP STERNDRIVE UNIT, Complete
5232100N1, 6211001N1, 6311002NZ, 6315001N1, 6315002NZ, 6416003N2, 6811001N1
5442300TP
STERNDRIVE, Bravo-III X (1.65:1 Ratio)
5442300TP STERNDRIVE, Bravo-III X (1.65:1 Ratio)
5232100TP, 6311002NZ, 6315002NZ, 6811001N1
5M42400TP
 
5M42400TP STERNDRIVE, Bravo III XR Diesel (1.81:1) Seacore
5232100TP, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900TS, 5E31910TP, 5E31910TS, 5E32200TP, 5E32900TS, 5E36200TP, 5E36200TS, 5E36210TP, 5E36210TS, 5E36800TP, 5E36800TS, 5E36810TP, 5E36810T
Back to top