36100 Mercruiser STUD, ADJUSTING-FRONT MOUNTING BRACKET (9 1/4")

Table 1
Diagnostic Trouble Codes    
CDL Code    J1939 Code    Code Description
(code descriptions may vary)    Comments    
E1008 (1)     3242-15     Aftertreatment 1 Diesel Particulate Filter Intake Gas Temperature High (1)     The temperature at the intake of the DPF exceeded a predetermined value.
Active regeneration is immediately disabled. The code is logged.    
E1008 (2)     3242-16     Aftertreatment 1 Diesel Particulate Filter Intake Gas Temperature High (2)     The temperature at the intake of the DPF exceeded a predetermined value.
Active regeneration is immediately disabled. The code is logged.    
Follow the troubleshooting procedure in order to identify the root cause of the problem.    
Table 2
Associated Diagnostic Trouble Codes    
3480-15
or E1050 (1)    
3480-16
or E1050 (2)    
4077-15
or 1051 (1)    
4077-16
or 1051 (2)    
Table 3
Troubleshooting Test Steps    Values    Results    
1. Check for Associated Diagnostic Trouble Codes
A. Establish communication between the Caterpillar Electronic Technician (ET) and the ECM. Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the "Warranty Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes.
Troubleshoot any associated diagnostic codes listed in Table 2 that are present before continuing with this procedure.
   
Associated codes
   
Result: An associated diagnostic trouble code is not active or logged.
Proceed to Test Step 2.
Result: An associated code is active or logged.
Troubleshoot the associated codes before continuing with this procedure.
Refer to Troubleshooting, "Diagnostic Trouble Codes" in order to troubleshoot the associated diagnostic code.
   
2. Check for High Exhaust Temperatures
A. Several factors can cause a calculated high exhaust temperature. Refer to "Troubleshooting, Exhaust Temperature Is High" for further information on calculated high exhaust temperatures
   
High exhaust temperatures
   
Result: The engine is experiencing high exhaust temperatures. Repair the cause of the high exhaust temperature.
Result: The engine is not experiencing high exhaust temperatures.
Proceed to Test Step 3.
   
3. Perform a manual cylinder cutout test.
A. Remove the inlet section (DOC) from the DPF.
B. Perform a manual cylinder cutout test. Manually cut out each cylinder while the exhaust is monitored. As each cylinder is cut out, look for a decrease in white smoke.
   
Faulty injector
   
Result: A faulty injector is found.
Replace any injectors that cause the engine to smoke and run rough when the cylinder is not cut out.
Clean the inside of the inlet section of the DPF.
Assemble the DPF. The engine must be run with no load at 1400 rpm for at least 15 minutes. If the white smoke continues after 15 minutes, the engine must continue to run until there is no white smoke.
Result: A faulty injector is not found.
Proceed to Test Step 4.
   
4. Inspect the DPF
A. Remove the inlet section (DOC) from the DPF.
B. Inspect the inside of the inlet section and the front face of the DPF. Look for oil and for excessive soot.
C. Inspect the inlet to the Diesel Oxidation Catalyst (DOC). Inspect the inlet of the catalyst and check the catalyst for plugging.
A small amount of soot is a normal condition. Contact your local technical communicator for Caterpillar engines if you suspect that the amount of soot is excessive. Continue with this procedure after you have received guidance from the technical communicator.
   
Oil, excessive soot or plugging
   
Result: Oil is found.
Perform the following procedure:
1. Inspect the outlet of the turbocharger. Clean the oil from the inside of the inlet section of the DPF.
2. Assemble the DPF. The engine must be run with no load at 1400 rpm for at least 15 minutes. If the white smoke continues after 15 minutes, the engine must continue to run until there is no white smoke.
Proceed to Test Step 5.
Result: Oil is not found.
Proceed to Test Step 5.
   Complete the procedure in the order in which the steps are listed.Refer to the OEM Troubleshooting Manual for more information. Contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).