43470 1 Mercruiser STUD, Bell Housing To Steering Bracket


43470 1 STUD, Bell Housing To Steering Bracket Mercruiser 5220200AS, 91331015 STUD
43470 1 STUD, Bell Housing To Steering Bracket Mercruiser
Rating:
103

Buy STUD, Bell Housing To Steering Bracket 43470 1 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 38
 

Compatible models:

5220200AS   91331015   Mercruiser

Mercruiser entire parts catalog list:

5220200AS 1988
91331015 1985,1986,1987

Information:

1. Remove three bolts and locks (1), and remove suction bell and tube (2) from the oil pump. 2. Remove bolts (3) that fasten elbow (5) and the tube assembly to the back of oil pump (6).
The oil pump idler gear can fall off the pump when the pump is removed. To prevent injury, always hold the gear on the pump when the pump is removed.
3. Remove four bolts and two locks (4), and remove oil pump (6) from the engine. The following steps are for installation of the oil pump.4. Put oil pump (6) in position, and install four bolts and two locks (4) that hold it in place.5. Install bolts (3) that hold elbow (5) and the tube assembly to the oil pump.6. Put suction bell and tube assembly (1) in position on the oil pump, and install three bolts and locks (1).End By:a. install oil panDisassemble Oil Pump
Start By:a. remove oil pump 1. Remove idler gear (2). Remove the bearing from the idler gear with tooling (B).2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), the keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (B).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (B) and a press as follows:a. Put bearings (9) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is 1.52 mm (.060 in.) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores. 2. Install the bearings in oil pump body assembly with tooling (B) and a press as follows.a. Put bearings (10) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See the topic, Oil Pump in the Specifications module.4. Put clean engine oil on all the parts of the oil pump. 5. Install pressure relief valve (11) cover (12) and bolt (6) in the oil pump body assembly. 6. Install shaft assemblies (13) in the oil pump body assembly.7. Install spacer (4). Install the key in the shaft assembly.8. Install the two gears on the shaft assemblies. 9. Install scavenge pump body assembly (14) and the bolts that hold it.10. Install key (15), drive gear (16), the washer and bolt (17). Tighten the bolt to a torque of 43 7 N m (32 5 lb.ft.).11. Install the bearing in the idler gear with tooling (B) and a press until it is even with the outside surface of the gear.12. Install the suction bell on the oil pump. Install the idler gear on the oil pump.
The oil pump must turn freely by hand after it is assembled.
End By:a. install oil pump


Parts stud Mercruiser:

56298
 
56298 STUD, GEAR HOUSING TO DRIVE SHAFT HOUSING (1 31/32"0
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 2250507, 5000165CE, 5220200AS, 91331015
56297
 
56297 STUD, WATER PUMP BASE AND BODY TO GEAR HOUSING (3 3/8")
00014332, 2140208, 2165208, 2250507, 5220200AS, 91331015
55422
 
55422 STUD, CONTROL PANEL TO BOAT (2")
00014332, 00019003, 01321017, 01326013, 03301310, 2140208, 2165208, 2250507, 5000165CE, 5220200AS, 6030000ES, 91331015
57921
 
57921 STUD, TRANSMISSION TO ENGINE (4")
02287333, 02297343, 04706002, 04707333, 08986342, 228801, 5220200AS, 91331015
57981
 
57981 STUD, ADAPTOR TO EXHAUST ELBOW (3")
30001854, 37011856, 5220200AS, 91331015
34816
 
34816 STUD (.437-20 x 2.500)
5220200AS, 91331015
57985
 
57985 STUD (2.810)
5220200AS, 91331015
53064 1
 
53064 1 STUD (7.280)
5220200AS, 91331015
Back to top