827512 Mercruiser STUD, Double End (3.125 x 1.25)


827512 STUD, Double End (3.125 x 1.25) Mercruiser 41510P1UE STUD
827512 STUD, Double End (3.125 x 1.25) Mercruiser
Rating:
68

Buy STUD, Double End (3.125 x 1.25) 827512 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 24
 

Compatible models:

41510P1UE   Mercruiser

Mercruiser entire parts catalog list:

41510P1UE 1998

Information:


Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
If the fuel system runs out of fuel or if air is introduced into the fuel system the following procedure may be followed.
Turn the ignition switch to the "OFF" position.
Fill the fuel tank (s) with clean diesel fuel.
Illustration 1 g01127321
(1) Fuel priming pump
(2) Air bleed
(3) Priming valve (If Equipped)
Turn the priming valve (3) (If Equipped) to the "Closed (Prime)" position in order to prime the fuel system.
Purging air from the fuel system requires the air bleed to be opened three full turns. Open air bleed (1). Do not remove the screw.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Crank the engine for 30 seconds. Use a suitable container to catch the fuel while you crank the engine. Allow the starter motor to cool for 2 minutes. Note: Most of the air should be purged from the system after four or five cranking cycles.
Repeat Step 5 until the engine starts and runs. If the engine runs rough, continue to operate the engine at low idle until the engine runs smoothly.
Observe air bleed (2). When a small drop of fuel appears at the threads of the air bleed, close and tighten air bleed (2). Note: Failure to tighten all fittings could result in serious fuel leaks.
After the engine has operated smoothly for 30 seconds, turn the priming valve (3) to the "Open (Run)" position. Note: Shortened injector life may occur if the priming valve (3) is left in the "Closed (Prime)" position.
Clean any residual fuel from the engine components.
Once the engine runs smoothly, stop the engine. Turn the ignition switch to the OFF position. Note: You may use the hand priming pump for the fuel filter (if equipped) instead of cranking the engine and running the engine. Perform the following procedure when the hand priming pump is used:
Illustration 2 g01127321
(1) Fuel priming pump
(2) Air bleed
(3) Priming valve (If Equipped)
Turn the priming valve (3) (If Equipped) to the "Closed (Prime)" position in order to prime the fuel system.
Purging air from the fuel system requires the air bleed (1) for the fuel filter to be opened three full turns. Open air bleed (1). Do not remove the screw.
While you operate the hand priming pump, observe the air bleed (2). When a small drop of fuel appears at the threads of the air bleed, close and tighten the air bleed (2). Note: Failure to tighten all fittings could result in serious fuel leaks.
Clean any residual fuel from the engine components.
Continue to operate the fuel priming pump (1) until a strong resistance is felt. Listen for an audible click from the fuel manifold. The click will indicate that the valve has opened and the fuel system is pressurized. Lock the fuel priming pump.
Do not crank the engine for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking again.
Crank the engine. If the engine starts but the engine runs rough, continue to operate the engine at low idle until the engine runs smoothly. Note: If the engine will not start, further priming is necessary. If the engine starts but the engine continues to misfire or smoke, further priming is necessary.
After the engine has operated smoothly for 30 seconds, turn the priming valve (3) to the "Open (Run)" position. Note: Shortened injector life may occur if the priming valve (3) is left in the "Closed (Prime)" position.Note: Some C11 Engines and C13 Engines may be equipped with a electric fuel priming pump.
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
If the engine's fuel system is run dry, fill the fuel tank. Then prime the fuel system in order to remove any air bubbles from the system.
Do not loosen fuel lines at the fuel manifold. The engine components may be damaged and/or loss of priming pressure may occur when the fuel lines are loosened.
The fuel system is equipped with an electronic fuel priming pump. When the ignition is turned to the ON position, the fuel system is automatically primed.


Parts stud Mercruiser:

34521
 
34521 STUD, VALUE ROCKER ARM (.013 O.S.)
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 07711346, 08986342, 08987343, 2165203, 2165208, 228801, 257B021JS, 260801, 30001854, 32001876, 40500
34522
 
34522 STUD, VLAUE ROCKER ARM ( 003 O.S.)
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 07711346, 08986342, 08987343, 2165203, 2165208, 228801, 257B021JS, 260801, 30001854, 32001876, 40500
64066
 
64066 STUD, STARTER MOTOR TO CYLINDER BLOCK
00014332, 01207333, 01402414, 01407333, 01701335, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 04708004, 04881333, 06661346, 07711346, 08986342, 08987343,
36100T
 
36100T STUD, ADJSUTING - FRONT MOUNTING BRACKET
01207333, 01402414, 01407333, 01701335, 41000001S, 41000008E, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS
806300
 
806300 STUD
4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS
805526
STUD (1/4-28 X 1-1/8 IN.)
805526 STUD (1/4-28 X 1-1/8 IN.)
41510P1UE, 4350118KS, 4441027LE, 444106AM1, 4542067LS, 4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
816327
 
816327 STUD, (.750-16 x Special)
4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 4V71222ND, 4V71222PD, 4V71222TD
866199
 
866199 STUD
41510P1UE
Back to top