862827 TETHER ASSEMBLY Mercruiser
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 4211015L1, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 4231017L1, 424106LRS, 424106LTT, 424106LU
TETHER
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$167.53
09-09-2022
-: -
OEM Transom Drain Plug Plugs Tether Assembly Kit 862827
OEM Transom Drain Plug Plugs Tether Assembly Kit 862827 || OEM Factory Tether and Drain Plug also includes the drain for the oil drain hose 1|4 pipe thread
OEM Transom Drain Plug Plugs Tether Assembly Kit 862827 || OEM Factory Tether and Drain Plug also includes the drain for the oil drain hose 1|4 pipe thread
$109.72
21-08-2022
-: -
TOTOTO Transom Drain Plug Plugs Tether Assembly Kit Compatible with Mercury Mercruiser 862827
Tether and Drain Plug || Part Number: 862827
Tether and Drain Plug || Part Number: 862827
Compatible models:
40430002S
40500006T
40500010T
40500010U
40500120U
41000001S
41000008E
4111021L1
4111021TS
4111021UT
4111021UU
411102KN2
41510P1UE
4211015L1
4211025RS
4211025TS
4211025TT
4211025US
4211025UU
4231017L1
424106LRS
424106LTT
424106LUS
424106PUU
444106LPS
444236HRS
4542067LS
4652027M1
4652227MW
4M11025LS
4M11025RS
4M11025TS
4M11025TT
4M11025US
4M4102LPS
4M4102LRS
4M4102LTS
4R42027N1
4S42028N1
4S42028TS
4S42028TT
4S42028UT
4S42028UU
4S420P8UE
Mercruiser
Mercruiser entire parts catalog list:
- OIL PAN, OIL PUMP AND REAR OIL SEAL » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- CYLINDER BLOCK, OIL PAN » 862827
- CYLINDER BLOCK, OIL PAN » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN, OIL PUMP AND REAR OIL SEAL » 862827
- OIL PAN, OIL PUMP AND REAR OIL SEAL » 862827
- OIL PAN, OIL PUMP AND REAR OIL SEAL » 862827
- OIL PAN, OIL PUMP AND REAR OIL SEAL » 862827
- OIL PAN, OIL PUMP AND REAR OIL SEAL » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN, OIL PUMP AND REAR OIL SEAL » 862827
- OIL PAN, OIL PUMP AND REAR OIL SEAL » 862827
- OIL PAN, OIL PUMP AND REAR OIL SEAL » 862827
- OIL PAN, OIL PUMP AND REAR OIL SEAL » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND OIL PUMP » 862827
- OIL PAN AND DRAIN SYSTEM » 862827
- OIL PAN AND DRAIN SYSTEM » 862827
- OIL PAN AND DRAIN SYSTEM » 862827
- OIL PAN AND DRAIN SYSTEM » 862827
- OIL PAN AND DRAIN SYSTEM » 862827
- OIL PAN AND DRAIN SYSTEM » 862827
Information:
References
Reference: Testing and Adjusting , "Fuel System Pressure - Test"Introduction
This procedure checks for air in the fuel. This procedure also helps with finding the source of the air.Required Tools
Table 1
Required Tools
Item Qty Part Number Part Name
T1 1 2P-8278 Tube As Test Preparation
Examine the fuel system for leaks. Ensure that the fuel line fittings are properly tightened. Check the fuel level in the fuel tank. Air can enter the fuel system on the suction side between the fuel transfer pump and the fuel tankTest Procedure
Install a 2P-8278 Tube As (SIGHT GAUGE) in the fuel return line. When possible, install the sight gauge in a straight section of the fuel line that is at least 304.8 mm (12 inches) long. Do not install the sight gauge near the following devices that create turbulence:
Elbows
Relief valves
Check valvesObserve the fuel flow during engine cranking. Look for air bubbles in the fuel. If there is no fuel in the sight gauge, prime the fuel system. Refer to Testing and Adjusting, "Fuel System - Prime" for more information. If the engine starts, check for air in the fuel at varying engine speeds. When possible, operate the engine under the conditions which have been suspect of air in the fuel.
Illustration 1 g01096678
2P-8278 Tube As (SIGHT GAUGE)
(1) A steady stream of small bubbles with a diameter of approximately 1.60 mm (0.063 inch) is an acceptable amount of air in the fuel.
(2) Bubbles with a diameter of approximately 6.35 mm (0.250 inch) are also acceptable if there are 2 seconds to 3 seconds intervals between bubbles.
(3) Excessive air bubbles in the fuel are not acceptable.
If excessive air is seen in the sight gauge in the fuel return line, install a second sight gauge at the inlet to the fuel transfer pump. If a second sight gauge is not available, move the sight gauge from the fuel return line and install the sight gauge at the inlet to the fuel transfer pump. Observe the fuel flow during engine cranking. Look for air bubbles in the fuel. If the engine starts, check for air in the fuel at varying engine speeds.If excessive air is not seen at the inlet to the fuel transfer pump, the air is entering the system after the fuel transfer pump. Proceed to Step 3 of “Adjustment Procedure”.If excessive air is seen at the inlet to the fuel transfer pump, air is entering through the suction side of the fuel system.Adjustment Procedure
To avoid damage, do not use more than 55 kPa (8 psi) to pressurize the fuel tank.
Pressurize the fuel tank to 35 kPa (5 psi). Do not use more than 55 kPa (8 psi) to avoid damage to the fuel tank. Check for leaks in the fuel lines between the fuel tank and the fuel transfer pump. Repair any leaks that are found. Check the fuel pressure to ensure that the fuel transfer pump is operating properly. For information about checking the fuel pressure, see Testing and Adjusting, "Fuel System Pressure - Test".
If the source of the air is not found, disconnect the supply line from the fuel tank and connect an external fuel supply to the inlet of the fuel transfer pump. If this action corrects the problem, repair the fuel tank or the stand pipe in the fuel tank.
If the injector sleeve is worn or damaged, combustion gases may be leaking into the fuel system. Also, if the O-rings on the injector sleeves are worn, missing, or damaged, combustion gases may leak into the fuel system.
Reference: Testing and Adjusting , "Fuel System Pressure - Test"Introduction
This procedure checks for air in the fuel. This procedure also helps with finding the source of the air.Required Tools
Table 1
Required Tools
Item Qty Part Number Part Name
T1 1 2P-8278 Tube As Test Preparation
Examine the fuel system for leaks. Ensure that the fuel line fittings are properly tightened. Check the fuel level in the fuel tank. Air can enter the fuel system on the suction side between the fuel transfer pump and the fuel tankTest Procedure
Install a 2P-8278 Tube As (SIGHT GAUGE) in the fuel return line. When possible, install the sight gauge in a straight section of the fuel line that is at least 304.8 mm (12 inches) long. Do not install the sight gauge near the following devices that create turbulence:
Elbows
Relief valves
Check valvesObserve the fuel flow during engine cranking. Look for air bubbles in the fuel. If there is no fuel in the sight gauge, prime the fuel system. Refer to Testing and Adjusting, "Fuel System - Prime" for more information. If the engine starts, check for air in the fuel at varying engine speeds. When possible, operate the engine under the conditions which have been suspect of air in the fuel.
Illustration 1 g01096678
2P-8278 Tube As (SIGHT GAUGE)
(1) A steady stream of small bubbles with a diameter of approximately 1.60 mm (0.063 inch) is an acceptable amount of air in the fuel.
(2) Bubbles with a diameter of approximately 6.35 mm (0.250 inch) are also acceptable if there are 2 seconds to 3 seconds intervals between bubbles.
(3) Excessive air bubbles in the fuel are not acceptable.
If excessive air is seen in the sight gauge in the fuel return line, install a second sight gauge at the inlet to the fuel transfer pump. If a second sight gauge is not available, move the sight gauge from the fuel return line and install the sight gauge at the inlet to the fuel transfer pump. Observe the fuel flow during engine cranking. Look for air bubbles in the fuel. If the engine starts, check for air in the fuel at varying engine speeds.If excessive air is not seen at the inlet to the fuel transfer pump, the air is entering the system after the fuel transfer pump. Proceed to Step 3 of “Adjustment Procedure”.If excessive air is seen at the inlet to the fuel transfer pump, air is entering through the suction side of the fuel system.Adjustment Procedure
To avoid damage, do not use more than 55 kPa (8 psi) to pressurize the fuel tank.
Pressurize the fuel tank to 35 kPa (5 psi). Do not use more than 55 kPa (8 psi) to avoid damage to the fuel tank. Check for leaks in the fuel lines between the fuel tank and the fuel transfer pump. Repair any leaks that are found. Check the fuel pressure to ensure that the fuel transfer pump is operating properly. For information about checking the fuel pressure, see Testing and Adjusting, "Fuel System Pressure - Test".
If the source of the air is not found, disconnect the supply line from the fuel tank and connect an external fuel supply to the inlet of the fuel transfer pump. If this action corrects the problem, repair the fuel tank or the stand pipe in the fuel tank.
If the injector sleeve is worn or damaged, combustion gases may be leaking into the fuel system. Also, if the O-rings on the injector sleeves are worn, missing, or damaged, combustion gases may leak into the fuel system.