8M0007689 Mercruiser TOOL, Bearing Installation, Propshaft


8M0007689 TOOL, Bearing Installation, Propshaft Mercruiser 5P4AB04HH, 5P4AB04IH, 5P4AZ54JH TOOL
8M0007689 TOOL, Bearing Installation, Propshaft Mercruiser
Rating:
103

Buy TOOL, Bearing Installation, Propshaft 8M0007689 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Compatible models:

Mercruiser entire parts catalog list:

5P4AB04HH 2007,2008
5P4AB04IH 2008
5P4AZ54JH 2008,2009

Information:


Table 1
Diagnostic Trouble Codes    
CDL Code    J1939 Code    Code Description
(code descriptions may vary)    Comments    
253-2     631-2     Personality Module : Erratic, Intermittent, or Incorrect     The flash file is for a different engine family or for a different engine application.
The engine will not start. Clearing this diagnostic code requires factory passwords. The personality module code must be reset to zero.    Flash programming is a method of programming or updating the flash file in the engine Electronic Control Module (ECM). Caterpillar Electronic Technician (ET) is used to flash program a file into the memory of the engine ECM.Note: Customer versions of CAT ET do not have the capability for flash programming. Consult your local Cat Dealer for assistance.If you do not have the flash file, use the "Flash File Search" tool on the Service Technician Workbench (STW) to obtain the flash file for your engine. Alternatively, use the "Service Software Files" feature on SIS Web to obtain the flash file for your engine. You must have the engine serial number in order to search for the flash file. After locating the correct flash file, download the flash file to your PC. Write down the name of the flash file for future reference.
Table 2
Troubleshooting Test Steps     Values     Results    
1. Programming a Flash File
A. Establish communication between Cat ET and the engine ECM.
B. Select "WinFlash" from the "Utilities" menu on Cat ET.
If "WinFlash" will not communicate with the ECM, refer to Troubleshooting, "Electronic Service Tool Does Not Communicate".
C. Program the flash file into the ECM.
D. Select the engine ECM under the "Detected ECMs".
E. Press the "Browse" button in order to select the name of the flash file that will be programmed into the ECM.
F. When the correct flash file is selected, press the "Open" button.
G. Verify that the "File Values" match the application. If the "File Values" do not match the application, obtain the correct flash file.
H. When the correct flash file is selected, press the "Begin Flash" button.
I. Cat ET will indicate when flash programming has been successfully completed.
J. Start the engine and check for proper operation. Repair any active diagnostic or event codes.
   
Programmed successfully    
Result: The flash programming was successfully.
Return the unit to service.
Result: The flash programming was not successfully.
Repair any active diagnostic or event codes. Proceed to Test Step 2.    
2. "WinFlash" Error Messages
A. If you receive any error messages during flash programming, click on the "Cancel" button in order to stop the process. Access the information about the "ECM Summary" under the "Information" menu. Make sure that you are flashing the correct file for your engine.
B. Record all error messages. The recorded error messages will be necessary if further assistance is needed.
   
Error messages    
Result: There are no error messages.
Return the unit to service.
   Complete the procedure in the order in which the steps are listed.Contact your Cat dealer Technical Communicator (TC) if further assistance is needed, your TC can confer with the Dealer Solutions Network (DSN).


Parts tool Mercruiser:

8M0007677
 
8M0007677 TOOL, Pinion Height Gage
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0007678
 
8M0007678 TOOL, Pinion Wrench Guide
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0007680
 
8M0007680 TOOL, Guide
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0021221
 
8M0021221 TOOL, Vertical Driveshaft Retaining Nut
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0029055
 
8M0029055 TOOL, Drive Alignment
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0030004
 
8M0030004 TOOL, Spline Adaptor
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0037221
 
8M0037221 TOOL, Bearing Driver
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0034342
 
8M0034342 TOOL, Backlash Wrench
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
Back to top