8M0007695 Mercruiser TOOL, Nose Cone Installation


8M0007695 TOOL, Nose Cone Installation Mercruiser 5P4AB04HH, 5P4AB04IH, 5P4AZ54JH TOOL
8M0007695 TOOL, Nose Cone Installation Mercruiser
Rating:
28

Buy TOOL, Nose Cone Installation 8M0007695 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 15
 

Compatible models:

Mercruiser entire parts catalog list:

5P4AB04HH 2007,2008
5P4AB04IH 2008
5P4AZ54JH 2008,2009

Information:


Table 1
Diagnostic Trouble Codes    
J1939 Code    CDL Code    Code Description    Comments    
1347-5     1779-5     Fuel Rail #1 Pressure Valve Solenoid : Current Below Normal     The Engine ECM detects a low current flow in the circuit for the solenoid driver.
The code is logged.    
1347-6     1779-6     Fuel Rail #1 Pressure Valve Solenoid : Current Above Normal     The Engine ECM detects a high current flow in the circuit for the solenoid driver.
The code is logged.    
1348-5     1780-5     Fuel Rail #2 Pressure Valve Solenoid : Current Below Normal     The Engine ECM detects a low current flow in the circuit for the solenoid driver.
The code is logged.    
1348-6     1780-6     Fuel Rail #2 Pressure Valve Solenoid : Current Above Normal     The Engine ECM detects a high current flow in the circuit for the solenoid driver.
The code is logged.    Note: The automatic cylinder cutout test is disabled while any of these codes are active.Automatic Configuration of the Solenoid DriversThe connectors for the solenoids are interchangeable. The ECM determines the connector that is connected to each solenoid during each engine start cycle. For this reason, either pump solenoid can be driven by either ECM driver.
Illustration 1 g03343251
Illustration 2 g01959043
Typical left side view
Illustration 3 g01959046
Harness connectors for the solenoids
Illustration 4 g01959049
(P2-50) Solenoid return (P2-68) Solenoid driver (P2-77) Solenoid driver (P2-111) Solenoid return
Table 2
Troubleshooting Test Steps    Values    Results    
1. Determine the Diagnostic Code
A. Establish communication between Cat® Electronic Technician (ET) and the applicable Electronic Control Module (ECM) . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the "Warranty Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes.
C. Look for an active or logged -5 code or -6 code.
   
Diagnostic Trouble Codes    
Result: There is an active or there is a logged -5 code
Proceed to Test Step 2.
Result: There is an active or there is a logged -6 code.
Proceed to Test Step 3.
   
Illustration 5 g03343300
Table 3
Troubleshooting Test Steps    Values    Results    
2. Check the Wiring for an Open Circuit
A. Turn the keyswitch to the OFF position.
B. Verify that the harness connector is free of debris, free of corrosion and securely connected.
C. Disconnect both solenoids from the harness.
D. Connect a jumper wire between terminals 1 and 2 of the harness connector for each coil. Each coil is replaced with a short circuit.
E. Turn the keyswitch to the ON position. Do not start the engine.
F. Connect to Cat ET. Select the Diagnostics tab and perform the "Fuel Rail Pump Solenoid Test".
   
Short Circuit    
Result: The test results indicate "Not OK (*Open)" for one or both solenoids.
There is an open circuit in the wiring between a solenoid and the Engine Electronic Control Module (ECM) connector. Check both solenoid wiring circuits. There may be a problem with a connector.
Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Verify that the original problem is resolved.
Perform the "Fuel Rail Pump Solenoid Test" again to verify that the problem is resolved.
Result: The test results indicate "Not OK (*Short)" for both solenoids.
The Engine Electronic Control Module (ECM) detected the jumper wires. There is a problem with a solenoid.
Repair: Replace the pump.
Perform the "Fuel Rail Pump Solenoid Test" again to verify that the problem is resolved.
   
Illustration 6 g03343302
Table 4
Troubleshooting Test Steps    Values    Results    
3. Check the Wiring for a Short Circuit
A. Verify that the harness connector is free of debris, free of corrosion and securely connected.
B. Connect to Cat ET, Select the Diagnostics tab, and perform the "Fuel Rail Pump Solenoid Test"
C. Reco


Parts tool Mercruiser:

8M0007677
 
8M0007677 TOOL, Pinion Height Gage
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0007678
 
8M0007678 TOOL, Pinion Wrench Guide
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0007680
 
8M0007680 TOOL, Guide
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0021221
 
8M0021221 TOOL, Vertical Driveshaft Retaining Nut
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0029055
 
8M0029055 TOOL, Drive Alignment
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0030004
 
8M0030004 TOOL, Spline Adaptor
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0037221
 
8M0037221 TOOL, Bearing Driver
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0034342
 
8M0034342 TOOL, Backlash Wrench
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
Back to top