76925A 6 Mercruiser TRANSMISSION ASSEMBLY, COMPLETE (MANUAL SHIFT)


76925A 6 TRANSMISSION ASSEMBLY, COMPLETE (MANUAL SHIFT) Mercruiser 03302336, 03307332 TRANSMISSION
76925A 6 TRANSMISSION ASSEMBLY, COMPLETE (MANUAL SHIFT) Mercruiser
Rating:
18

Buy TRANSMISSION ASSEMBLY, COMPLETE (MANUAL SHIFT) 76925A 6 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Compatible models:

03302336   03307332   Mercruiser

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1
B 8T-5096 Dial Indicator 1
C 8T-3052 Degree Wheel 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.
Illustration 1 g06239408
Position new upper main bearing (6) on the crankshaft. Insert the end of the upper main bearing that does not have the tab into the cylinder block. Install Tooling (A) in the oil hole of the crankshaft. Carefully rotate the crankshaft to push the upper main bearing into the cylinder block.Note: Push the upper main bearing from the side of the bearing tab with Tooling (A). If the crankshaft is pushed the wrong direction, the bearing tab will be pushed between the crankshaft and the bearing area of the cylinder block. This action can result in damage to the cylinder block and/or the crankshaft.
Illustration 2 g06239416
Install the thrust plates (7) on each side of the number 4 main bearing.Note: Install the thrust plates with the words "Block Side" toward the cylinder block.
Install the lower halves of the crankshaft main bearings in the main bearing caps.Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the main bearing caps.
Illustration 3 g06239102
Position main bearing caps (4) on the crankshaft.Note: Ensure that the numbers on the main bearing caps match the numbers on the cylinder block. Also ensure that the "FRONT" on the main bearing cap is installed toward the front of the cylinder block.
Lubricate the threads of bolts (3) and bolts (5) with clean engine oil. Install the bolts.
Tighten bolts (3) and bolts (5) for the main bearing caps, as follows:
Tighten bolt (3) on the tab end to a torque of 258 14 N m (190 10 lb ft).
Tighten Bolt (3) on the opposite end to a torque of 258 14 N m (190 10 lb ft).
Tighten Bolt (3) on the opposite end an additional 120 5 degrees.Note: If Tooling (C) is not used, place an index mark on the bolt and the main bearing cap.
Tighten Bolt (3) on the tab end an additional 120 5 degrees .Note: If Tooling (C) is not used, place an index mark on the bolt and the main bearing cap.
Tighten Bolt (5) on the opposite side to a torque of 80 10 N m (59 7 lb ft).
Tighten Bolt (5) on the tab end to a torque of 80 10 N m (59 7 lb ft).
Repeat Step 6e thru Step 6f.
Rotate the crankshaft to ensure that the crankshaft turns freely.
Use Tooling (B) to check the crankshaft end play. Ensure that Tooling (B) is against a machined surface. The end play is controlled by the thrust plates of No. 4 main bearing (center).Crankshaft end play (new thrust plates) ... 0.10 to 0.60 mm (0.004 to 0.024 inch)End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".


Parts transmission Mercruiser:

47754A 9
 
47754A 9 TRANSMISSION ASSEMBLY (10-18 SERIES)
03307332, 03308333, 04544347, 30001854, 44031854
47753A 7
 
47753A 7 TRANSMISSION ASSEMBLY (10-17 SERIES)
03307332, 03308333, 04544347, 37011856
60958
Back to top