76214A 2 Mercruiser TRIM TAB ASSEMBLY


76214A 2 TRIM TAB ASSEMBLY Mercruiser 5120150AR, 5220200AS TRIM
76214A 2 TRIM TAB ASSEMBLY Mercruiser
Rating:
8

Buy TRIM TAB ASSEMBLY 76214A 2 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$22.74
 

28-07-2021
0.17[0.00] Pounds
-: -
Sierra 18-6244 Magnesium Anode
Material: Magnesium || Designed for use with Mercury/Mariner 35-300 HP engines, Force 90 and 120 HP engines 1995 and newer, and Mercruiser Alpha One Gen II and Bravo I, II, III, X, XR, XZ || Provides additional clearance for high rake propellers || Interchangeable with Mercruiser Stern Drive 762142, 76214A1, 76214A2, 76214A5, 97-76214Q5, and Mercury Marine 76214, 762142, 762143, 76214A1, 76214A5, 76214T3, 97-762145, 97-76214Q5 || Each Sierra product meets or exceeds the original equipment part it replaces. || Fit type: Universal Fit
Number on catalog scheme: 8
 

Compatible models:

5120150AR   5220200AS   Mercruiser

Mercruiser entire parts catalog list:

5120150AR 1988,1989,1990,1991,1992,1993,1994,1995
5220200AS 1988

Information:

1. Remove the plug from location (1). Install tool (A) in the hole with the square end down. Move the governor control to the "ON" position until the rack stops against tool (A). The racks are now in center (zero) position. 2. Disconnect lines (2) from the fuel injection pumps. Put caps on all fuel openings.3. Use tool (B) to loosen the bushings. 4. Remove fuel injection pump with tool (C). Remove tool (C) and bushing (3) from the fuel injection pump. Remove the washer from bushing (3) and remove seal from under bushing.
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed back in their original location.
5. Disassemble the fuel injection pump. Remove ring (4). Make a separation of the bonnet from the plunger and barrel assembly (5).
Be careful when the injection pumps are disassembled. Do not cause damage to the surface on the plunger. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
6. Remove the gear segment, washer and spring from the barrel.7. Remove the ring, spring, collar, and valve from the barrel. 8. Remove spacer (6) from the fuel injection pump housing.Install Fuel Injection Pumps
Make sure the fuel racks are in the center (zero) position before the fuel injection pumps are installed. 1. Put plunger (5), washer (6) and spring (4) in position on barrel (9). Put check valve assembly (3) and spring (8) in position in bonnet (7). Connect bonnet (7) and barrel (9) together with ring (2). Keep seal (1) with bonnet for use at installation. 2. Put spacer (12) into position in the pump housing bore. Make sure the correct spacer is with each pump.3. Put the spacer in gear segment (10) in alignment with the groove in barrel (9). 4. Put the injection pump straight down into the housing bore so the space in gear segment (10) is in alignment with pin (11) and the groove in barrel (9) is in alignment with dowel (13). Use tool (C) to install the pump. 5. Install seal (1) and bushing (14) in the pump housing bore. If the pump is in the correct position, bushing (14) will turn into the threads of the pump housing with the fingers until it is even with the housing. Tighten bushing (14) to a torque of 150 10 lb.ft. (205 14 N m) with tool (B).6. Install the washer on bushing (14).7. Connect the fuel lines to the injection pumps and tighten fuel line nuts to a torque of 30 5 lb.ft. (40 7 N m).8. Check for correct installation of the injection pumps with the engine stopped. See INSTALLATION OF INJECTION PUMP in TESTING AND ADJUSTING.
If one or more of the injection pumps have been installed wrong, damage to the engine is possible if cautions are not taken when the engine is first started. Make preparation to close off the air intake to stop the engine, if necessary.
9. Remove the timing pin [tool (A)] and install the plug in the injection pump housing.


Parts trim Mercruiser:

31640A 1
TRIM TAB ASSEMBLY
31640A 1 TRIM TAB ASSEMBLY
00014332, 00019003, 01321017, 01326013, 03301310, 2140208, 2165208, 2250507, 5000165CE, 5220200AS, 6030000ES, 91331015
68258A 4
 
68258A 4 TRIM MOTOR SOLENOID
01321017, 03301310, 5220200AS, 91331015
47342A12
 
47342A12 TRIM CYLINDERS ASS'Y, COMPLETE
01321017, 03301310, 5220200AS, 6030000ES, 91331015
46399A 1
98704A17
TRIM CYLINDER, Starboard
98704A17 TRIM CYLINDER, Starboard
5120136JS, 5120150AR, 5220200AS, 5231100LP, 5C30150FS, 6020006JS, 6211001N1, 6311002NZ, 6315002NZ, 6416003N2, 6511102N1, 6811001N1
98703A17
TRIM CYLINDER, Port
98703A17 TRIM CYLINDER, Port
5120136JS, 5120150AR, 5220200AS, 5231100LP, 5C30150FS, 6020006JS, 6211001N1, 6311002NZ, 6315002NZ, 6416003N2, 6511102N1, 6811001N1
Back to top