41672 1 Mercruiser TUBE, Water, WATER (3/4 inch I.D. WATER TUBE)


41672 1 TUBE, Water, WATER (3/4 inch I.D. WATER TUBE) Mercruiser 00019003, 01321017, 01326013, 5000147JS, 5000150DP, 5000165CE, 5111200LP TUBE

Buy TUBE, Water, WATER (3/4 inch I.D. WATER TUBE) 41672 1 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 26
 

Mercruiser entire parts catalog list:

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
101-13
Engine Crankcase Pressure : Out of Calibration 101-13
Crankcase Air Pressure Sensor : Out of Calibration During key on, the signal voltage from the crankcase air pressure sensor indicated a crankcase air pressure greater than +/- 1.5 kPa (0.2 psi).
There is not a reference sensor for this sensor
109-13
Engine Coolant Pressure : Out of Calibration 109-13
Engine Coolant Outlet Pressure Sensor : Out of Calibration During key on, the signal from the coolant pressure sensor does not fall within a tunable threshold of the atmospheric pressure sensor.
Reference sensor : Atmospheric Pressure Sensor
411-13
Engine Exhaust Gas Recirculation Differential Pressure : Out of Calibration 3387-13
EGR Differential Pressure Sensor : Out of Calibration During key on, the signal voltage from the EGR differential pressure sensor indicated a differential pressure greater than +/- 11 kPa (2 psi).
There is not a reference sensor for this sensor
3358-13
Engine Exhaust Gas Recirculation Inlet Pressure : Out of Calibration 3385-13
EGR Intake Pressure Sensor : Out of Calibration During key on, the signal voltage from the EGR intake pressure sensor indicated an EGR intake pressure greater than +/- 18 kPa (3 psi) from the atmospheric pressure sensor.
Reference sensor : Atmospheric Pressure Sensor
3563-13
Engine Intake Manifold #1 Absolute Pressure : Out of Calibration 1785-13
Intake Manifold Pressure Sensor : Out of Calibration During key on, the signal voltage from the Intake Manifold pressure sensor indicated an Intake Manifold pressure greater than +/- 18 kPa (3 psi) from the Atmospheric Pressure sensor.
Reference sensor : Atmospheric Pressure Sensor
5422-13
Engine Intake Manifold #2 Absolute Pressure : Out of Calibration 3031-13
Intake Manifold #2 Pressure Sensor : Out of Calibration During key on, the signal voltage from the Intake Manifold pressure sensor indicated an Intake Manifold pressure greater than +/- 18 kPa (3 psi) from the Atmospheric Pressure sensor.
Reference sensor : Atmospheric Pressure Sensor
5708-13
Engine Coolant Pressure #2 : Out of Calibration 4626-13
Engine Coolant Intake Pressure Sensor : Out of Calibration During key on, the signal from the coolant pressure sensor does not fall within a tunable threshold of the atmospheric pressure sensor.
Reference sensor : Atmospheric Pressure Sensor
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
Note: The engine coolant temperature must be greater than 0° C (32° F) before beginning this procedure.
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Look for active codes that are associated with the system for the event code.
Codes
Result: An associated code is active.
Repair: Troubleshoot any associated codes before continuing with this test.
Result: A 109-13, 2802-13, or 5708-13 is active or logged.
Proceed to Test Step 3.
Result: Any other code is active or logged.
Proceed to Test Step 2.
2. Check for Debris
A. Turn the keyswitch to the OFF position.
B. Check the sensor for debris.
C. If applicable, check the reference sensor for debris.
D. Check the sensor measurement port for blockage by debris.
E. If debris is found, clear the debris from the measurement port and replace the sensor.
F. Connect Cat ET.
G. Use Cat ET to monitor the following:
- Codes
Note: Some applications may be equipped with a breather element on the atmospheric pressure sensor. Inspect the breather element for plugging, along with the sensor port.
Debris
Result: The sensor measurement port is not blocked by debris.
Proceed to Test Step 3.
Result: A -13 code is not active.
Return to service.
Result: A -13 code is active.
Repair: Replace the sensor. If more than one -13 code is active and the codes have a reference sensor, replace the reference sensor.
If the problem is not resolved, proceed to Test Step 3.
3. Inspect the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Inspect the sensor connector for moisture and corrosion.
Moisture
Result: The sensor connector does not have moisture or corrosion.
Proceed to Test Step 5.
Result: The sensor connector has moisture and/or corrosion.
Proceed to Test Step 4.
4. Remove any moisture and/or corrosion
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor connector.
C. Remove any moisture and/or corrosion from the outside of the connector. Check for moisture and corrosion inside the connector. Verify that the seals for the wires are sealing correctly. Refer to Troubleshooting, "Electrical Connectors - Inspect" for additional information.
D. If necessary, repair or replace the connector.
E. Reconnect the connector. Verify that the connection is secure.
F. Connect Cat ET.
G. Use Cat ET to monitor the following:
- Codes
Moisture
Result: A -13 code is not active.
Return the service.
Result: A -13 code is active.
Repair: Replace the sensor. If more than one -13 code is active and the codes have a reference sensor, replace the reference sensor.
If the problem is not resolved, proceed to Test Step 5.
5. Check for Moisture and/or Corrosion in the Circuit
A. Turn the keyswitch to the OFF position.
B. Check all the connectors in the circuit for moisture and/or corrosion.
C. Check for corrosion inside the connector. Verify that the seals for the wires are sealing correctly. Refer to Troubleshooting, "Electrical Connectors - Inspect" for additional information.
D. If necessary, repair or replace the connector.
E. Reconnect the connector. Verify that the connection is secure.
F. Connect Cat ET.
G. Use Cat ET to monitor the following:
- Codes
Moisture
Result: A -13 code is not active.
Return the service.
Result: A -13 code is active.
Repair: Replace the sensor. If more than one -13 code is active and the codes have a reference sensor, replace the reference sensor.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts tube Mercruiser:

54236
 
54236 TUBE, WATER - WATER POCKET COVER
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 2250507, 5000165CE
55112
 
55112 TUBE, CABLE GUIDE
00014332, 01206002, 01207333, 01321017, 01326013, 01406002, 01407333, 02287333, 02607333, 03301310, 03302336, 03307332, 04706002, 04707333, 08986342, 2140208, 2165208, 2250507, 228801, 260801, 30001854, 37011856, 44031854
78458A 1
TUBE, EXHAUST
78458A 1 TUBE, EXHAUST
00014332, 00019003, 01321017, 01326013, 02602347, 02608427, 04544347, 06661346, 2140208, 2165208, 257B021JS, 457B100KS, 4V71222PD, 4V71222TD, 5000165CE, 5120136JS, 5120150AR, 5220200AS, 5231100LP, 5232100N1, 5C30150FS, 5E31200N1, 5E31200TP, 5E31200TS
78632A 1
 
78632A 1 TUBE, EXHAUST
01321017, 03301310
55104
 
55104 TUBE, EXTENDING - POWER STEERING
01206002, 01207333, 01326013, 01406002, 01407333
55105
 
55105 TUBE, RETRACTING - POWER STEERING
01206002, 01207333, 01326013, 01406002, 01407333
86907 1
 
86907 1 TUBE, WATER -5/8 inch I.D. WATER TUBE
00019003, 01321017, 01326013, 5000165CE
815935T
 
815935T TUBE, Port Cylinder
5000147JS, 5000150DP, 5000165CE, 5111200LP
Back to top