58616A 2 Mercruiser TUBE, WATER SEPARATION (3" O.D. ELBOW ONLY)


58616A 2 TUBE, WATER SEPARATION (3" O.D. ELBOW ONLY) Mercruiser 00014332, 01854335, 02287333, 02297343, 02607333, 02608427, 03307332, 03308333, 04544347, 07711346, 08987343, 30001854, 37011856, 44031854 TUBE
58616A 2 TUBE, WATER SEPARATION (3" O.D. ELBOW ONLY) Mercruiser
Rating:
53

Buy TUBE, WATER SEPARATION (3" O.D. ELBOW ONLY) 58616A 2 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Mercruiser entire parts catalog list:

00014332 1982
01854335 1985,1986
02287333 1983
02297343 1983,1985,1986
02607333 1983
02608427 1987
03307332 1982
03308333 1983,1984,1985,1987
04544347 1987
07711346 1986,1987
08987343 1983,1984,1985,1986,1987
30001854 1984,1986
37011856 1986,1987
44031854 1984

Information:

The following conditions must exist before any of the preceding codes will become active:
The ECM has been powered for at least 2 seconds.
There are no active 168 codes.
There are no active 3509 (262) codes.Use this procedure to troubleshoot the position sensors for the following valves:
NRS valve
Engine intake throttle valve
Combustion air valve for the Aftertreatment Regeneration Device (ARD)Each position sensor is integral in the associated valve. If the following procedure indicates a fault with the position sensor, then the entire valve must be replaced.The following background information is related to this procedure:The troubleshooting procedures for the diagnostic codes of each position sensor are identical. The 5 VDC sensor supply provides power to all 5 VDC sensors. The ECM supplies 5.0 VDC to terminal "5" of the engine intake throttle valve connector and to terminal "1" of the other valve connectors. The sensor common from the ECM connector goes to terminal "3" of the engine intake throttle valve connector. The sensor common from the ECM connector goes to terminal "2" of the other valve connectors. The sensor supply is output short circuit protected. A short circuit to the battery will not damage the circuit inside the ECM. The signal voltage from terminal "4" of the engine intake throttle valve is supplied to the appropriate terminal at the P2 ECM connector. The signal voltage from terminal "3" of the other valves is supplied to the appropriate terminal at the P2 ECM connector.Pull-up VoltageThe ECM continuously outputs a pull-up voltage on the circuit for the sensor signal wire. The ECM uses this pull-up voltage to detect an open in the signal circuit. When the ECM detects a voltage above a threshold on the signal circuit, the ECM generates an open circuit diagnostic code (XXXX-3) for the sensor.If the sensor is disconnected, pull-up voltage at the sensor connector indicates that the wires are not open or shorted to ground. If the sensor is disconnected , the absence of pull-up voltage indicates an open in the signal wire or a short to ground. If the sensor is disconnected and the voltage is different from pull-up voltage, the signal wire is shorted to another wire in the harness.
Illustration 1 g06156781
Schematic diagram for the valve position sensors
Illustration 2 g01981373
Typical view of the pin locations on the P2 connector for the position sensors
(3) Engine intake throttle valve position sensor signal
(15) NRS valve position sensor signal
(16) Combustion air valve position sensor signal
(45) Combustion air valve position sensor 5 VDC supply
(46) Engine intake throttle valve, NRS valve position sensors 5 VDC supply
(55) Combustion air valve position sensor ground
(56) Engine intake throttle valve, NRS valve position sensors ground
Illustration 3 g02186473
Typical view of the pin locations for the valve position sensors on the connectors from the engine to the Clean Emissions Module (CEM)
(1) 5 VDC supply
(2) Combustion air valve position sensor ground
(9) Combustion air valve position sensor signal
Illustration 4 g03177615
Connector for the NRS valve
(1) 5 VDC supply
(2) Position sensor ground
(3) Position sensor signal
Illustration 5 g03177636
Connector for the combustion air valve
(1) 5 VDC supply
(2) Position sensor ground
(3) Position sensor signal


Parts tube Mercruiser:

58616A 1
 
58616A 1 TUBE, WATER SEPARATION-EXHAUST ELBOW
03302336, 03307332, 2165203, 2165208, 2888203
77442A 1
TUBE KIT
77442A 1 TUBE KIT
00014332, 2140208, 2165208, 2250507
87173
 
87173 TUBE, OUTER
00014332, 2140208, 2165208
90949T
TUBE, Exhaust
90949T TUBE, Exhaust
01207333, 01402414, 01407333, 01701335, 03307332, 03308333, 04544347, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS
92163A 2
 
92163A 2 TUBE, OIL LEVEL GAUGE
00014332, 02287333, 02607333, 02608427, 07711346, 08987343, 30001854, 32001876
96511A 1
 
96511A 1 TUBE ASSEMBLY, STEERING
30001854, 32001876, 5000150DP, 5000165CE, 5120150AR, 5220200AS
94068
Back to top