806754T Mercruiser TUBE PLASTIC ROCKER COVER


806754T TUBE PLASTIC ROCKER COVER Mercruiser 40430002S, 4211015L1, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 4231017L1, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 4262C01JT, 443B1003S, 443B100JS, 443HC00JT TUBE
806754T TUBE PLASTIC ROCKER COVER Mercruiser
Rating:
13

Buy TUBE PLASTIC ROCKER COVER 806754T Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Mercruiser entire parts catalog list:

40430002S 1998
4211015L1 1998
4211025RS 1998
4211025TS 1998
4211025TT 1998
4211025US 1998
4211025UU 1998
4231017L1 1998
424106LRS 1998
424106LTT 1998
424106LUS 1998
424106PUU 1998
4262C01JT 1996,1997
443B1003S 1993,1994,1995
443B100JS 1996
443HC00JT 1996,1997

Information:

For removal of the governor from the fuel injection pump housing, see Disassemble Governor. 1. Remove cover (1). 2. Install tooling (B). Engage the timing pin in the center groove of the fuel rack. Move the fuel rack in the direction of the arrow to find the center groove.3. Install tooling (D), and remove bushing (2). 4. Install tooling (E), and remove the fuel injection pump. 5. Remove spacer (3). Do not mix components from fuel injection pump assemblies.6. Remove the remainder of the fuel injection pumps and spacers with Steps 2-5 done again for each injection pump. 7. Remove cover (4). 8. Remove fuel rack (5). 9. Use a bar magnet to remove lifter assembly (6). Put identification marks on the lifter assemblies as to their location in the fuel injection pump housing. 10. Use tooling (A) to remove snap ring (7). Do not let the camshaft fall because the machined surfaces will be scratched.11. Use a plastic hammer to make camshaft (8) move out of washer (9). 12. Remove camshaft (8). 13. Remove rack rear bearing (10) and camshaft rear bearing (11). 14. Install location plate from tooling (B). Align the bore in the plate with the O-ring seal counterbore in the fuel injection pump housing. Make a mark for alignment.15. Remove tooling (B). 16. Remove rack bearing (12) and camshaft bearing (13).Assemble Fuel Injection Pump Housing
Be sure all oil passages are clear, and put clean engine oil on all parts before assembly. 1. Use tool (A) to install the camshaft rear (governor end) bearing. Install the bearing with the joint toward the top of the fuel injection pump housing. Install the bearing so it is 1.00 0.25 mm (.039 .010 in.) below the surface of the housing. 2. Use tooling (A) to install the fuel rack rear (governor end) bearing. Install the bearing so it is 7.16 0.13 mm (.282 .005 in.) below the surface of the housing. 3. Install the plate assembly from tooling (B) on the drive end of the fuel injection pump housing to install the bearing for the fuel rack. Use clean grease to hold the new fuel rack bearing on the driver from tooling (B). Install the driver and bearing in the plate assembly with the groove in the driver in alignment with the pin in the plate assembly, and use a hammer to push the bearing into position. The bearing will be installed to the correct depth when the shoulder of the driver is against the plate assembly.4. Remove tooling (B) from the fuel injection pump housing. The rack bearing must be installed so it is 0.25 0.25 mm (0.010 0.010 in.) below the surface of the housing. 5. Install fuel injection pump camshaft (1) in the fuel injection pump housing.6. Put the fuel injection pump housing on end, and put a block under the camshaft. 7. Put washer (2) over the end of the camshaft, and use tooling (A) and (C) to push washer (2) against its seat on the camshaft. The camshaft must have 0.285 0.235 mm (0.0112 0.0093 in.) end play when the washer is pushed against cam shoulder. 8. Use tool (D) to install snap ring (3) in the groove in the camshaft.
If the original lifters are to be installed, be sure to install them in their respective bores in the pump housing. New lifters can be mixed.
9. Install four lifter assemblies (4) in the fuel injection pump housing with the groove in the lifter in alignment with the pin in the housing. 10. Install fuel rack (5) in the fuel injection pump housing. Install the rack with the groove in the end of fuel rack in alignment with the ear (tab) of the rack bearing at the drive end of the fuel injection pump housing. 11. Install the timing pin from tooling (B). Engage the timing pin in the center groove of the fuel rack. Move the fuel rack in the direction of the arrow to locate the center groove.12. Install spacer (6). 13. Put (slot) groove (8) in the gear segment 180° away from groove (7) in the barrel. When the fuel injection pump is installed, groove (7) must engage the dowel (9). 14. Use tool (E) to install the fuel injection pump. Installation is made easier by rotation of the cam lobe away from the lifter assembly. 15. Install O-ring seal (10). 16. Install bushing (11). Tighten bushing (11) by hand until the bushing is even with the top of the housing. If installation of the bushing can not be made this far by hand, remove it. Remove the pump, put the parts in alignment again, and install the bushing again.17. Use tool (F) and a torque wrench to tighten the bushing to a torque of 163 14 N m (120 10 lb.ft.).18. Remove tooling (B). 19. Install tooling (G) and (H) to measure total rack travel. Correct rack travel is 15.70 mm (.618 in.). A smaller measurement is an indication of incorrect fuel injection pump installation.20. Complete the installation of the remainder of fuel injection pumps as given in Steps 11-19. 21. Install cover (12) and gasket.22. Install the governor on the fuel injection pump housing. See Assemble Governor; then install the fuel injection pump housing and governor on the engine.


Parts tube Mercruiser:

12117A 5
 
12117A 5 TUBE, OIL LEVEL GAUGE
01751347, 443B0002S, 443B1003S, 443B100JS
44348T
TUBE, Exhaust
44348T TUBE, Exhaust
02602347, 02608427, 257B021JS, 40280001D, 40280002D, 40420001D, 40420002D, 40430002S, 4111021L1, 4111021TS, 411102KN2, 4211015L1, 4211025RS, 4211025TS, 4211025TT, 4231017L1, 424106LRS, 4262C01JT, 428B116KD, 430B00001, 430L000JS, 4332087N1, 4350100KS,
14358T
TUBE
14358T TUBE
02602347, 02608427, 257B021JS, 40430002S, 4211015L1, 4211025RS, 4211025TS, 4211025TT, 4231017L1, 424106LRS, 4262C01JT, 4332087N1, 4350100KS, 4350104JS, 4350104KS, 4350111HS, 4350118JS, 4350118KS, 443B0002S, 443B1003S, 443B100JS, 443HC00JT, 4441027LE,
807458T
 
807458T TUBE, Exhaust
4211015L1, 4231017L1, 4262C01JT, 443HC00JT
807454T
 
807454T TUBE, Dipstick
4262C01JT, 443HC00JT
44348001
TUBE, Exhaust, Exhaust
44348001 TUBE, Exhaust, Exhaust
40500006T, 40500010T, 40500010U, 40500120U, 4111021UT, 4111021UU, 41510P1UE, 4211025US, 4211025UU, 424106LTT, 424106LUS, 424106PUU, 4M11025US, 4S420P8UE
863841T
TUBE, Water (Brass)
863841T TUBE, Water (Brass)
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS
14358001
TUBE, Exhaust, Exhaust
14358001 TUBE, Exhaust, Exhaust
40500006T, 40500010T, 40500010U, 40500120U, 4211025US, 4211025UU, 424106LTT, 424106LUS, 424106PUU, 4M11025TS, 4M11025US, 4S420P8UE
Back to top