87717A 2 Mercruiser TUBE, OIL LEVER GAUGE


87717A 2 TUBE, OIL LEVER GAUGE Mercruiser 01207333, 01402414, 01407333, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 430B00001, 430L000JS TUBE
87717A 2 TUBE, OIL LEVER GAUGE Mercruiser
Rating:
38

Buy TUBE, OIL LEVER GAUGE 87717A 2 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$75.99

06-12-2024
0.25[0.11] Pounds
US: Modern Boat Sales, I
Mercury - Mercruiser Tube Assy, 87717A-2
Quiksilver New
Number on catalog scheme: 1
 

Mercruiser entire parts catalog list:

01207333 1983
01402414 1984,1985,1986,1987,1988,1989
01407333 1983
4111021L1 1998
4111021TS 1998
4111021UT 1998
4111021UU 1998
411102KN2 1998
430B00001 1990,1991,1992,1993,1994,1995
430L000JS 1996,1997

Information:

Probable Causes
Active codes and logged codes
Electrical connections
Unstable fuel supply
Switches
Circuit protection
Engine speed/timing
Table 1
Associated Diagnostic Trouble Codes
J1939 Code CDL Code
3719-0 E995 (3)
3719-16 E995 (2)
5246-0 E1389 (3) Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 2
Troubleshooting Test Steps Values Results
1. Active Codes and Logged Codes
A. Certain diagnostic codes and/or event codes may cause an engine shutdown. Connect the electronic service tool and check for active codes and for logged codes.
B. Use the electronic service tool to check for associated diagnostic trouble codes. Refer to Table 1
Codes
Result: There are associated diagnostic trouble codes active or logged.
Repair: Troubleshoot any active or logged associated diagnostic trouble codes before continuing with this procedure.
Result: There are no associated diagnostic trouble codes active or logged.
Proceed to Test Step 2.
2. Electrical Connections
A. Check for the correct installation of the ECM J1/P1 and the J2/P2 connectors. Check for correct installation of the fuel injector connectors.
Connectors
Result: There are suspect connectors.
Repair: Perform the "Wiggle Test" on the electronic service tool.
Repair or replace connectors that are suspect.
Result: There are no suspect connectors.
Proceed to Test Step 3.
3. Electrical Connections
A. Check the power and ground connections to the ECM. Refer to Troubleshooting, "Electrical Power Supply - Test".
Electrical Connectors
Result: The electrical connections are OK.
Proceed to Test Step 4.
Result: The electrical connections are not OK.
Repair: Repair or replace the damaged connectors. Verify that the repair eliminated the fault.
4. Unstable Fuel Supply
A. Inspect the fuel system. Refer to Systems Operation/Testing and Adjusting, "Fuel System - Inspect" for additional information.
Note: Cold weather adversely affects the characteristics of the fuel. Refer to the engine Operation and Maintenance Manual, "Cold Weather Operation" for further information.
B. Check fuel quality. Check the fuel tank for debris or foreign objects which may block the fuel supply.
Fuel
Result: The fuel quality is OK.
Proceed to Test Step 5.
Result: The fuel quality is not OK.
Repair: Replace the fuel. Verify that the repair eliminated the fault.
5. Switches
A. Check the keyswitch input to the ECM.
B. Check any engine shutdown switches and associated wiring.
Switches
Result: The shutdown switches and wiring are OK.
Proceed to Test Step 6.
Result: The shutdown switches and wiring are not OK.
Repair: Make the necessary repairs, Verify that the repair eliminated the fault.
6. Circuit Protection
A. Inspect the wires and connectors to all circuit protection for the engine.
B. Check the device for circuit protection.
Circuit protection
Result The circuit protection device is tripped.
Repair: Reset the circuit breakers if the circuit breakers are tripped. If necessary, replace blown fuses. Prior to returning the engine to service, determine the condition that caused the circuit breaker to trip or the fuse to blow. Make the necessary repairs.
Result The circuit protection device is OK.
Proceed to Test Step 7.
8. Engine Speed/Timing Sensors
A. Inspect the connectors for the engine speed/timing sensors.
B. Crank the engine. If the engine starts and no speed timing codes are logged, the speed timing circuit is operating correctly.
Speed/Timing
Result: The Speed/Timing sensor circuit is not operating correctly.
Repair: Test the speed/timing circuit. Refer to Troubleshooting, "Speed/Timing - Test". Verify that the repair eliminated the fault.
If the fault is still present, contact the Dealer Solutions Network (DSN).


Parts tube Mercruiser:

55112
 
55112 TUBE, CABLE GUIDE
00014332, 01206002, 01207333, 01321017, 01326013, 01406002, 01407333, 02287333, 02607333, 03301310, 03302336, 03307332, 04706002, 04707333, 08986342, 2140208, 2165208, 2250507, 228801, 260801, 30001854, 37011856, 44031854
73815 2
 
73815 2 TUBE, SIGHT, PUMP TO CARBURETOR
01206002, 01207333, 01326013, 01406002, 01407333, 02287333, 04706002, 04707333, 04856332, 08986342, 228801
87717A 1
 
87717A 1 TUBE, OIL LEVER GAUGE
01206002, 01207333, 01326013, 01406002, 01407333
53370
55104
 
55104 TUBE, EXTENDING - POWER STEERING
01206002, 01207333, 01326013, 01406002, 01407333
55105
 
55105 TUBE, RETRACTING - POWER STEERING
01206002, 01207333, 01326013, 01406002, 01407333
90949T
TUBE, Exhaust
90949T TUBE, Exhaust
01207333, 01402414, 01407333, 01701335, 03307332, 03308333, 04544347, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS
44348
 
44348 TUBE, EXHAUST
00014332, 01207333, 01402414, 01407333, 01751347, 01854335, 02287333, 02607333, 02608427, 03307332, 03308333, 04544347, 06661346, 07711346, 08987343, 4454110AS
Back to top