879194243 Mercruiser VALVE, Solenoid - On/Off - 12V


879194243 VALVE, Solenoid - On/Off - 12V Mercruiser 5P4AB04HH, 5P4AB04IH, 5P4AZ54JH VALVE
879194243 VALVE, Solenoid - On/Off - 12V Mercruiser
Rating:
33

Buy VALVE, Solenoid - On/Off - 12V 879194243 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$664.05
 

19-08-2022
0.0947[0.04] Pounds
-: -
New Mercury Mercruiser Quicksilver Oem Part # 879194243 Solenoid Valve
Number on catalog scheme: 16
 

Compatible models:

Mercruiser entire parts catalog list:

5P4AB04HH 2007,2008
5P4AB04IH 2008
5P4AZ54JH 2008,2009

Information:


Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
If the fuel system runs out of fuel, or if air is introduced into the fuel system, the following procedure may be followed.
Turn the ignition switch to the "OFF" position.
Fill the fuel tank with clean diesel fuel.
Illustration 1 g01927544
Illustration 2 g01927558
View of area A
(1) Fuel regulator valve
(2) Fuel return line from cylinder head
(3) Air purge
Illustration 3 g01927569
(4) Fuel priming pump
Turn the priming valve (If Equipped) to the "Closed (Prime)" position in order to prime the fuel system.
Purging air from the fuel system requires the air purge to be opened three full turns. Open air purge (3). Do not remove the screw.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Crank the engine for 30 seconds. Use a suitable container to catch the fuel while you crank the engine. Allow the starting motor to cool for 2 minutes. Note: Most of the air should be purged from the system after four or five cranking cycles.
Repeat Step 5 until the engine starts and runs. If the engine runs rough, continue to operate the engine at low idle until the engine runs smoothly.
Observe air purge (3). When a small drop of fuel appears at the threads of the air purge, close and tighten air purge (3). Note: Failure to tighten all fittings could result in serious fuel leaks.
After the engine has operated smoothly for 30 seconds, turn the priming valve to the "Open (Run)" position. Note: Shortened injector life may occur if the priming valve is left in the "Closed (Prime)" position.
Clean any residual fuel from the engine components.
Once the engine runs smoothly, stop the engine. Turn the ignition switch to the OFF position. Note: You may use the hand priming pump for the fuel filter (if equipped) instead of cranking the engine and running the engine. Perform the following procedure when the hand priming pump is used:
Illustration 4 g01451302
(1) Fuel priming pump
(2) Air purge
(3) Priming valve (If Equipped)
Turn the priming valve (3) (If Equipped) to the "Closed (Prime)" position in order to prime the fuel system.
Purging air from the fuel system requires the air purge (2) for the fuel filter to be opened three full turns. Open air purge (2). Do not remove the screw.
While you operate the hand priming pump, observe the air purge (2). When a small drop of fuel appears at the threads of the air purge, close and tighten the air purge (2). Note: Failure to tighten all fittings could result in serious fuel leaks.
Clean any residual fuel from the engine components.
Continue to operate the fuel priming pump (1) until a strong resistance is felt. Listen for an audible click from the fuel manifold. The click will indicate that the valve has opened and the fuel system is pressurized. Lock the fuel priming pump.
Do not crank the engine for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking again.
Crank the engine. If the engine starts but the engine runs rough, continue to operate the engine at low idle until the engine runs smoothly. Note: If the engine will not start, further priming is necessary. If the engine starts but the engine continues to misfire or smoke, further priming is necessary.
After the engine has operated smoothly for 30 seconds, turn the priming valve (3) to the "Open (Run)" position. Note: Shortened injector life may occur if the priming valve (3) is left in the "Closed (Prime)" position.


Parts valve Mercruiser:

8M0022194
VALVE, Control
8M0022194 VALVE, Control
5P4AB04HH, 5P4AB04IH
879194245
VALVE, Proportional - 12V
879194245 VALVE, Proportional - 12V
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
Back to top