813974 Mercruiser VOLTAGE REGULATOR


813974 VOLTAGE REGULATOR Mercruiser 01207333, 01402414, 01407333, 01751347, 02602347, 02608427, 04544347, 06661346, 4052110CR, 430B00001, 44541101S, 4454110AS, 45021102S, 474H110AR VOLTAGE
813974 VOLTAGE REGULATOR Mercruiser
Rating:
58

Buy VOLTAGE REGULATOR 813974 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$364.33
 

01-06-2024

Amazon.com
Wells A06789 Voltage Regulator
Wells Voltage regulators control the charging voltage that the alternator produces, commonly keeping it between 13.5 and 14.5 V, to protect the electrical components throughout the vehicle || When not replaced, the battery will discharge or over charge (destroying battery), engine will die, CEL will illuminate, charging system light will illuminate, or alternator damage may occur || Designed to meet or exceed OE specifications in form, fit and function
$36.76
 

15-12-2023
2.36[1.06] pounds
US: Race-Driven Inc
Sprocket for KTM 530 EXC 2009-2011 Rear 48 Tooth Sprocket by Race-Driven
Race-Driven Brand New 48 Tooth Rear Steel Sprocket || Race-Driven sprockets are manufactured to exceed OEM specifications || Race-driven sprockets are produced using hardened S45C steel || Fits: 2009 2010 2011 KTM 530 EXC
Number on catalog scheme: 29
 

Mercruiser entire parts catalog list:

01207333 1983
01402414 1984,1985,1986,1987,1988,1989
01407333 1983
01751347 1987,1988,1989,1990,1991,1992
02602347 1987,1988,1989,1990,1991,1992,1993,1994,1995
02608427 1987
04544347 1987
06661346 1986,1987,1988,1989
4052110CR 1990,1991,1992
430B00001 1990,1991,1992,1993,1994,1995
44541101S 1991,1992,1993,1994,1995,1996
4454110AS 1988,1989,1991,1992
45021102S 1992,1993
474H110AR 1988,1989,1990,1991

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 1U-6684 Piston Ring Compressor 1
C 227-4390 E12 Torx Socket 1
D 8T-3052 Degree Wheel 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
If the connecting rod caps were temporarily installed, remove the connecting rod caps. If necessary, thoroughly clean all of the components.
Apply clean engine oil to the cylinder bore, piston rings, outer surface of the piston and the bearing shells for the connecting rod. Note: Install the bearing shells for the connecting rods dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check" for the correct procedure. Apply clean engine oil to the bearing shells for the connecting rods during final assembly.Note: Ensure that the piston and the connecting rod assembly are installed in the correct cylinder.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom center position. Lubricate the crankshaft pin with clean engine oil.
Illustration 1 g02013213
Install Tooling (B) onto piston (4). Note: Ensure that Tooling (B) is installed correctly and that piston (4) can easily slide from the tool.Note: The arrow on the top of the piston must be toward the front of the engine. The locating tab for the bearing shell of the connecting rod must be on the same side of the engine as the piston cooling jet.
Carefully push the piston and the connecting rod assembly into the cylinder bore and onto the crankshaft pin. Note: Do not damage the finished surface of the crankshaft pin.
Illustration 2 g02383096
Install connecting rod cap (2) onto connecting rod (1). Note: Ensure that etched number in Position (X) on connecting rod cap (2) matches etched number in Position (X) on connecting rod (1). Ensure the correct orientation of connecting rod cap (2). The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old bolts in order to secure the connecting rod cap.
Install new bolts (3) to connecting rod (1). Use Tooling (C) in order to tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts for an additional 120 degrees in a clockwise direction. Use Tooling (C) and Tooling (D) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft in order to ensure that there is no binding.
Repeat Step 2 through Step 9 in order to install the remaining pistons and connecting rods. End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install" for the correct procedure.
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" for the correct procedure.


Parts voltage Mercruiser:

7036
 
7036 VOLTAGE REGULATOR
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01851333, 01854335, 02287333, 02297343, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 06661346, 07711346, 08986342, 08987343, 228801, 260801, 30001854, 3200
78385
 
78385 VOLTAGE REGULATOR, TRANSISTOR
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 08986342
Back to top