53212 Mercruiser WASHER


53212 WASHER Mercruiser 5220200AS, 91331015 WASHER
53212 WASHER Mercruiser
Rating:
68

Buy WASHER 53212 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

Compatible models:

5220200AS   91331015   Mercruiser

Information:


To prevent possible personal injury, do not disconnect any hydraulic lines until all the hydraulic pressure has been released from the system.
Start By:a. drain all fluids from the engine systems 1. Remove four bolts (1).2. Remove tube (2).3. Remove tube (3). 4. Remove two screws (3).5. Remove nut (4).6. Remove support clamp from throttle cable and air filter assembly frame.7. Position linkage (5) for clearance during engine removal. 8. Disconnect two fuel lines (6) for clearance during engine removal.9. Disconnect two fuel lines (8) for clearance during engine removal. Fuel lines are clamped to the engine at three locations. Remove bolts and aside fuel line assemblies from engine for clearance while removing the engine.10. Disconnect two electrical connections (7). 11. Disconnect four nuts (9) to remove wiring harness before engine removal. Mark or identify wiring for later assembly. 12. Repeat Step 10 on starter on opposite side of the engine. Mark or identify wiring for later assembly. 13. Remove clamps and wiring harness (10) from the block to the engine oil sensor and the shutoff solenoid to allow for engine removal. 14. Loosen four hose clamps (11).15. Aside hose (12) for engine removal. 16. Disconnect fuel line (13). 17. Loosen two hose clamps (14).18. Disconnect hose (15) from tube (16).19. Remove tube (16). 20. Cut the wire ties (17) on the filter assembly frame that secure the harness for exhaust temperature sensor and the speed sensor on the flywheel housing. Disconnect sensors and aside. 21. Remove the three front floor plates (18) (two are shown as removed) for clearance during the engine removal. 22. Cut wire ties from the dipstick. Remove dipstick and bracket assembly (19) from engine. 23. Remove floor plate as shown on rear of engine.24. Support the air filter assembly frame with hoist and straps.25. Loosen hose clamps and slide two exhaust/turbo boots from the air filters.26. Remove the bolts (20) from the two support rods at the base of the air filter assembly base.27. Remove eight bolts (21) (not shown) from the base of the air filter assembly frame and engine flywheel housing.28. Remove air filter assemblies (22).29. Remove cutter belt guard by disconnecting four pins and one brace with two bolts.30. Release belt tension and aside cutter drive belt for clearance during engine removal. 31. Disconnect hose (23) from cutter drive manifold. Remove two bolts (25) from hose support bracket (24). Set assembly aside.32. Mark and identify all wires from the main harness (main harness is on the left front side of the engine) to the components. Disconnect and remove the harness to provide clearance for the engine removal.33. Attach a lifting device and hoist to the engine. 34. Remove two bolts (26). 35. Remove four bolts (27) on rear of engine.36. Remove two bolts (not shown) that mount cutter housing clutch assembly to the engine.
Damage could occur to the housing if these two bolts are not removed before engine removal.
Check all steps for completion and begin raising engine slowly checking periodically to make sure all disconnections or removals have been made. For installation of the 3412 (Engine A), reverse the removal steps. Refer to the Service Manual KENR1688 for procedure to adjust belt tension.End By:a. fill engine systems to correct level


Parts washer Mercruiser:

29245
 
29245 WASHER, ROCKER COVER CHIMENY STUD
00014332, 00019003, 01206002, 01207333, 01321017, 01326013, 01402414, 01406002, 01407333, 01701335, 01751347, 01851333, 01854335, 02287333, 02602347, 02607333, 02608427, 03301310, 03307332, 03308333, 04544347, 06661346, 07711346, 08986342, 08987343,
20553
 
20553 WASHER, IGNITION COIL SCREW
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01701335, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 04708004, 04856332, 06661346,
24676
 
24676 WASHER, WIRING HARNESS CLAMP FASTING SCREW
00014332, 00019003, 01206002, 01207333, 01321017, 01326013, 01406002, 01407333, 03301310, 2140208, 2165203, 2165208, 2250507, 32001876, 5000165CE, 5220200AS, 6030000ES, 91331015
54012
 
54012 WASHER, BELL HOUSING STUD
01321017, 03301310, 4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE, 5220200AS, 5231100TP, 5232100TP, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900TS, 5E31910TP, 5E31910TS,
92721
 
92721 WASHER, PINION GEAR
00019003, 01321017, 01326013, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5220200AS, 91331015
19183
 
19183 WASHER, Fiber
44541101S, 4454110JT, 4454118JT, 4502111FE, 474L118JS, 474L118JT, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5120136JS, 5120150AR, 5220200AS, 5231100LP, 5C30150FS, 6020006JS, 6211001N1, 6311002NZ, 6315002NZ, 6416003N2, 6511102N1, 6811001N1, 91331015
19479
 
19479 WASHER
5220200AS, 91331015
817260
 
817260 WASHER
5220200AS, 91331015
Back to top