811399 Mercruiser WASHER


811399 WASHER Mercruiser 442B110GD, 442B115KD WASHER
811399 WASHER Mercruiser
Rating:
48

Buy WASHER 811399 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$36.95
 

23-02-2024
1.28[0.58] pounds
US: Race-Driven Inc
Ball Joints fit Can-Am Renegade 500 2013-2015 Upper x2 by Race-Driven
Race-Driven Race-Driven Upper Ball Joint || Ball Joints are designed to meet or exceed OEM specifications || Fits: 2013 2014 2015 Can-Am Renegade 500
Number on catalog scheme: 6
 

Compatible models:

442B110GD   442B115KD   Mercruiser

Mercruiser entire parts catalog list:

442B110GD 1994,1995,1996,1998
442B115KD 1997

Information:

2. Disconnect hose (3) and (6) from the bottom of water pump (5).3. Disconnect heater hose (2) from the valve.4. Remove the clip, bolts and retainers (1) that fasten tube (4) to the water pump and remove tube (4) from the water pump.
Typical Example5. Fasten a nylon strap and a hoist to the water pump.6. Remove bolts (8) that fasten the water pump to adapter (7). Remove bolts (9) that fasten the water pump to the front drive housing and remove the water pump. The weight of the water pump is 40 kg (88 lb.). 7. Remove elbow assembly (10) and the seal from water pump (5).8. Install the water pump in the reverse order of removal.9. Replace all seals and gaskets with new ones.10. Fill the cooling system with coolant and check for leaks. Refer to the Operations And Maintenance Manual for further information.Disassemble Water Pump
Start by:a. remove water pump 1. Remove O-ring seal (4) from the back of housing assembly (3).2. Remove washer (1) that holds shaft assembly (2) in housing assembly (3).
Typical Example3. Remove cover (5) from housing assembly (3). Remove the O-ring seal from cover (5).
Typical Example4. Loosen bolt (7) holding impeller (6) to the pump shaft. Use tooling (A) to loosen impeller (6) from the end of the pump shaft. Remove tooling (A), bolt (7), the washer and impeller (6) from the pump shaft and housing assembly (3).
Typical Example5. Remove spring (9) from seal assembly (8) and shaft assembly (2).6. Use a soft hammer, and push shaft assembly (2) out of seal assembly (8) and housing assembly (3). Remove seal assembly (8) from housing assembly (3). 7. Remove ceramic seal (10) from the rubber ring. Remove the rubber ring from housing assembly (3). 8. Remove seal (11) from the back of housing assembly (3).Assemble Water Pump
1. If necessary, make a replacement of the two filters in the pump housing at location (12).2. If necessary, make a replacement of plug (13) and the seal beneath plug (13).3. Use tooling (A) to install seal (11) into housing (3). Make sure the lip of the seal faces toward the outside as shown. Lubricate the lip seal (11) with clean engine oil. 4. Install shaft assembly (2) into housing (3). Install thrust washer (1) and the bolts to hold shaft assembly (2) in position.
Use clean water as the only lubricant when installing seal group (8). Use care when handling seal group (8) during installation onto pump shaft (2). Touching the wear surfaces of the carbon or ceramic rings can cause contamination or damage. Install the smoothest face of the ceramic ring toward the carbon seal assembly.
5. Put ceramic seal (10) in position in the rubber ring. Use hand pressure and tool (B) to install the ceramic seal.
Typical Example6. Remove the spring from seal assembly (8). Use hand pressure and tool (B) to install the seal assembly. Push the seal assembly on the shaft until the seal faces make light contact.
Typical Example7. Install spring (9) on the carbon seal assembly.8. Put impeller (6) in position on the pump shaft as shown.
Typical Example9. Install the washer and bolt (7). Tighten bolt (7) to a torque of 200 25 N m (150 18 lb. ft.). 10. Make sure the studs for cover (5) are tightened in the pump housing. Torque the three studs to 45 7 N m (33 7 lb ft).11. Install the O-ring seal on cover (5). Lubricate the O-ring seal with clean engine oil. Position cover (5) onto the pump housing. Install and evenly tighten the nuts for cover (5). Torque the nuts holding cover (5) to 27 4 N m (20 3 lb. ft.).End By:a. install water pump


Parts washer Mercruiser:

7024
 
7024 WASHER, CONDENSOR TERMINAL STUD
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 06661346, 07711346, 08986342, 08987343, 228801, 260801, 3000
811460
 
811460 WASHER
40280001D, 40280002D, 40420001D, 40420002D, 428B116KD, 442B110GD, 442B115KD, 473B116KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND, 4V71222ND, 4V71222PD, 4V71222TD
40022 17
 
40022 17 WASHER
40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C8204DLD, 4CJ2040ND
811459
 
811459 WASHER
40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C8204DLD, 4CJ2040ND
811455
 
811455 WASHER
40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
854098
WASHER
854098 WASHER
40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
813297
 
813297 WASHER
428B116KD, 442B110GD, 442B115KD, 4A72040ND
813303
 
813303 WASHER
428B116KD, 442B110GD, 442B115KD, 4A72040ND
Back to top