865491A01 Mercruiser YOKE, Coupler End


865491A01 YOKE, Coupler End Mercruiser 5111200LP YOKE
865491A01 YOKE, Coupler End Mercruiser
Rating:
23

Buy YOKE, Coupler End 865491A01 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$281.77
 

28-05-2024

CN: nusind
Generic U Joint Assembly, High Reliability 86481A2 High Strength Steel Alloy for Mercruiser Gen I II R MR, Genericuhk0g2word
Generic Compatible OE Numbers: This U Joint Assembly is compatible with part numbers 864281A2, 18‑6402, 18‑6405, 18‑921, 59830A5, 814819A2, 814819A7, 864281A01, 864281A2, 86481A2, 865491A01, and 8964281A2. || Enhanced Performance: The U Joint Assembly features a precise design that ensures smooth and efficient performance. It helps improve the performance of your boat, enhancing maneuverability and overall speed. || Applicable Models: Fit for Mercruiser One Gen I 83‑90; Fit for Mercruiser One Gen II 91‑97; Fit for Mercruiser One SS 86‑89; Fit for Mercruiser R MR One 83‑90; Fit for Mercruiser Bravo I II III 88‑95. || Construction: Made from steel alloy materials with special coating, this U joint assembly is built to withstand the harsh marine environment. It offers excellent resistance to rust, ensuring long lasting performance and reliability. || Easy Replacement: With its precise design and dimensions, this U Joint Assembly can be easily installed as a direct replacement. No modifications or additional parts are required, saving you time and effort.
$282.58
 

28-05-2024

CN: Wandisy
86481A2, U Joint Assembly, Construction for Mercruiser Gen I II R MR
Naroote Compatible OE Numbers: This U Joint Assembly is compatible with part numbers 864281A2, 18‑6402, 18‑6405, 18‑921, 59830A5, 814819A2, 814819A7, 864281A01, 864281A2, 86481A2, 865491A01, and 8964281A2. || Applicable : Fit for Mercruiser One Gen I 83‑90; Fit for Mercruiser One Gen II 91‑97; Fit for Mercruiser One SS 86‑89; Fit for Mercruiser R MR One 83‑90; Fit for Mercruiser Bravo I II III 88‑95. || Easy Replacement: With its precise design and dimensions, this U Joint Assembly can be easily installed as a direct replacement. No modifications or additional parts are required, saving you time and effort. || Enhanced Performance: The U Joint Assembly features a precise design that ensures smooth and efficient performance. It helps improve the performance of your boat, enhancing maneuverability and overall speed. || Construction: Made from steel alloy materials with special coating, this U joint assembly is built to withstand the harsh marine environment. It offers excellent resistance to rust, ensuring long lasting performance and reliability.
Number on catalog scheme: 13
 

Compatible models:

5111200LP   Mercruiser

Mercruiser entire parts catalog list:

5111200LP 1998

Information:


Table 1
Diagnostic Trouble Codes
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
3483-11 E1305 (1) Initial Assembly Aftertreatment #1 Procedure Required Initial assembly of the aftertreatment system is complete or the Engine ECM or the A5:E2 Aftertreatment Controller was replaced.
3530-31 E1040 (2) ARD Manually Disabled The regeneration system is disabled by the electronic service tool.
3716-15 E1300 (1) Aftertreatment Regeneration Cannot Start Due to Low Engine Temperature The coolant temperature is below 40° C (104° F) and the Diesel Particulate Filter inlet temperature is below 50° C (122° F).
If the ambient temperature is 0° C (32° F) or below, the coolant temperature must be 60° C (140° F) for active regeneration to begin.
3703-31 E993 (3) DPF Active Regeneration Inhibited Due to Inhibit Switch The regeneration system is disabled due to the ARD Disable Switch in the operator interface.
3712-15 E1301 (1) Aftertreatment Regeneration Cannot Start Due To System Fault There is an active fault related to the ARD combustion air system, ARD fuel system, or ARD ignition system.
3716-31 E1300 (2) Aftertreatment Regeneration Cannot Start Due To Low Engine Temperature The coolant temperature is below 40° C (104° F) and the Diesel Particulate Filter inlet temperature is below 50° C (122° F).
If the ambient temperature is 0° C (32° F) or below, the coolant temperature must be 60° C (140° F) for active regeneration to begin.
3750-15 E1302 (1) Aftertreatment Regeneration Cannot Start Due To Conditions Not Met One or more conditions are not allowing an Aftertreatment Regeneration to start, Refer to Test Step 7.
3750-31 E1239 (1) DPF #1 Conditions Not Met for Active Regeneration The operator did not allow enough time for regeneration to occur. The operator must respond when the DPF lamp is illuminated. The operator must allow the engine to idle until the regeneration is complete. Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Diagnostic Codes that are Active
A. Establish communication between the electronic service tool and the Electronic Control Module (ECM). Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Check and record any event codes that are active or logged.
Diagnostic Code
Result: A 3750-31 (E1239 (3)) diagnostic code is present.
Proceed to Test Step 2.
Result: A 3703-31 (E993 (3)) diagnostic code is present.
Proceed to Test Step 3.
Result: A 3530-31 (E1040 (2)) diagnostic code is present.
Proceed to Test Step 4.
Result: A 3716-15 (E1300 (1)) or 3716-31 (E1300 (2)) diagnostic code is present.
Proceed to Test Step 5.
Result: A 3712-15 (E1301 (1)) diagnostic code is present.
Proceed to Test Step 6.
Result: A 3750-15 (E1302 (1)) or diagnostic code is present.
Proceed to Test Step 7.
Result: A 3483-11 (E1305 (1)) diagnostic code is present.
Proceed to Test Step 8.
2. A 3750-31(E1239 (1))
A. The operator did not allow regeneration to occur or automatic regeneration did not occur within the required time limit. The operator must respond when the DPF lamp is illuminated.
B. Perform a "Forced Regeneration" by pressing the "Regeneration Force Switch" button.
Forced Regeneration
Result: The "Forced Regeneration" was successful.
Return the unit to service.
Result: The "Forced Regeneration" was not successful.
Repair: Troubleshoot the active diagnostic codes.
3. A 3703-31E993 (3) Diagnostic Code is Present
A. The operator has disabled the regeneration system and regeneration is necessary.
Disabled Regeneration
Result: Perform a manual DPF regeneration. Refer to the Operation and Maintenance Manual, "Diesel Particulate Filter Regeneration" for the proper operation of the regeneration system.
Return the unit to service.
4. A 3530-31 (E1040 (2)) Diagnostic Code is Present
A. The regeneration system is disabled by the electronic service tool.
Regeneration Disabled by the electronic service tool.
Result: Establish communication between the electronic service tool and the engine ECM. Set the value of the "Aftertreatment Regeneration Device" from "Disabled" to "Enabled".
Return the unit to service.
5. A 3716-15 (E1300 (1)) or 3716-31 (E1300 (2)) diagnostic code is present
A. The engine temperature is too low for an aftertreatment regeneration.
Low Engine Temperature
Result: Raise the coolant temperature above 40° C (104° F) and the Diesel Particulate Filter inlet temperature above 50° C (122° F). If the ambient temperature is −15° C (5° F) or below, the coolant temperature must be above 60° C (140° F) for active regeneration to begin.
Return the unit to service.
6. A 3712-15 (E1301 (1)) diagnostic code is present.
Note: Aftertreatment regeneration cannot start due to a system fault.
A. Establish communication between the electronic service tool and the engine Electronic Control Module (ECM).
B. Check for active faults related to the ARD combustion air system, ARD fuel system, or ARD ignition system.
System Fault
Result: Troubleshoot all active faults related to the ARD combustion air system, ARD fuel system, or ARD ignition system. Clear any active codes after correcting the faults. Activate regeneration.
Return the unit to service.
7. A 3750-15 (E1302 (1)) or diagnostic code is present
Note: Aftertreatment regeneration


Parts yoke Mercruiser:

814819A 3
YOKE, Coupler End
814819A 3 YOKE, Coupler End
5000147JS, 5000150DP, 5000165CE, 5111200LP
853635
864282T
 
864282T YOKE, Gear End
5111200LP, 5S21800TS
Back to top