41323A 2 Mercury STEERING LINK ATTACHING KIT


41323A 2 STEERING LINK ATTACHING KIT Mercury 10202014D, 1020201DB, 1020201VB, 1F10203VD, 1F10352VD, 1F13203FB STEERING
41323A 2 STEERING LINK ATTACHING KIT Mercury
Rating:
38

Buy STEERING LINK ATTACHING KIT 41323A 2 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$70.49
 

26-09-2017

Mercury &a: Mercury & Mercru
Attaching Kit, Mercury - Mercruiser 41323A-2
Number on catalog scheme: &nbsp
 

Mercury entire parts catalog list:

10202014D 1994,1995,1996,1997,1998
1020201DB 2005,2006
1020201VB 1999,2000,2001,2002,2003,2004
1F10203VD 1999,2000,2001,2002,2003,2004,2005
1F10352VD 1999
1F13203FB 2006

Information:


Table 1
Diagnostic Codes Table
CDL Code J1939 Code Code Description Comments
110-3 110-3 Engine Coolant Temperature Sensor : Voltage Above Normal The code is logged if the engine has been running for more than seven minutes. The Electronic Control Module (ECM) uses the last valid engine coolant temperature. If the diagnostic code is active at start-up, the ECM will use intake manifold temperature. When the intake manifold air temperature is not valid, the ECM will default to 90 °C (194 °F) for engine coolant temperature. The ECM will activate the cooling fan after this code has been active for more than eight seconds.
110-4 110-4 Engine Coolant Temperature Sensor : Voltage Below Normal
172-3 Intake Manifold Air Temperature Sensor : Voltage Above Normal The ECM will log the diagnostic code. The ECM will flag the intake manifold air temperature as invalid data. Also, the intake manifold air temperature is set to a default value of 40 °C (104 °F).
172-4 Intake Manifold Air Temperature Sensor : Voltage Below Normal
174-3 174-3 Fuel Temperature Sensor : Voltage Above Normal The code is logged. The ECM will flag the fuel temperature as invalid data and the fuel temperature is set to a default value of 40 °C (104 °F).
174-4 174-4 Fuel Temperature Sensor : Voltage Below Normal
2526-3 172-3 Air Inlet Temperature Sensor : Voltage Above Normal The code is logged.
The ECM detects voltage that is not in the acceptable range.
2526-4 172-4 Air Inlet Temperature Sensor : Voltage Below Normal The code is logged.
The ECM detects voltage that is not in the acceptable range. System OverviewThe sensor signal for the passive sensor is routed from the ECM to terminal 1 of each sensor connector. The sensor return for the passive sensors is routed to the ECM from terminal 2 of each sensor connector.Diagnostics on the Caterpillar Electronic Technician (ET)Wiggle Test - The Wiggle Test allows you to monitor the status of the signals from the sensors.For additional information regarding the Wiggle Test, refer to the documentation that accompanies the Cat ET software.
Illustration 1 g01155187
Terminal locations at the connector for the passive analog sensors
(Terminal 1) Sensor signal
(Terminal 2) Analog sensor return
Illustration 2 g03019119
Table 2
Troubleshooting Test Steps Values Results
1. Check for Diagnostic Trouble Codes
A. Connect to Caterpillar Electronic Technician (ET).
B. Turn the keyswitch to the ON position.
C. Access the "Active Diagnostic Code" screen on Cat ET.
Wait at least 30 seconds in order for the diagnostic codes to become active.
D. Look for these active codes or logged codes:
1. -3
2. -4
Codes
Result: A -3 diagnostic code is active.
Proceed to Test Step 2.
Result: A -4 diagnostic code is active.
Proceed to Test Step 3.
2. Create a Short at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the suspect sensor.
C. Install the jumper wire between terminal 1 (sensor signal) and terminal 2 (sensor return) at the sensor connector.
D. Turn the keyswitch to the ON position.
E. Monitor the diagnostic codes on Cat ET. Check for an active -4 diagnostic code for the suspect sensor.
Wait at least 30 seconds in order for the diagnostic codes to become active.
F. Turn the keyswitch to the OFF position.
Short circuit recognized
Result: The -3 diagnostic code remains active for the suspect sensor.
There is an open in the harness. Repair the wiring or replace the harness.
Verify that the problem is resolved.
Result: A -4 diagnostic code became active after creating the short at the sensor connector.
The wiring is OK. Replace the sensor.
Verify that the problem is resolved.
3. Create an Open at the Suspect Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor connector of the suspect sensor with the active -4 diagnostic code.
C. Turn the keyswitch to the ON position.
D. Monitor the diagnostic codes on Cat ET. Check for an active -3 diagnostic code for the suspect sensor.
Wait at least 30 seconds in order for the diagnostic codes to become active.
E. Turn the keyswitch to the OFF position.
Open circuit recognized
Result: The -4 diagnostic code remains active for the suspect sensor.
There is an open in the harness. Repair the wiring or replace the harness.
Verify that the problem is resolved.
Result: A -3 diagnostic code became active after disconnecting the sensor.
The wiring is OK. Replace the sensor.
Verify that the problem is resolved.
Complete the procedure in the order in which the steps are listed.If the procedure corrected the issue, return the engine to service.If the procedure did not correct the issue, Contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts steering Mercury:

816667A 2
STEERING BRACKET (W/O CARRYING HANDLE)
816667A 2 STEERING BRACKET (W/O CARRYING HANDLE)
10202014D, 1020201DB, 1020201VB, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 1050302SD, 1055207DB, 1055207UD, 1055207VB, 1A30302ZB, 1A40302FD, 1A40302HZ, 1A40303KZ, 1A40311FZ, 1A40311HZ, 1A40403HZ, 1A40412HZ, 1A41412Z
825650
 
825650 STEERING CABLE
1F08203VF, 1F08261RF, 1F10352VD
821468A66
STEERING HANDLE ARM
821468A66 STEERING HANDLE ARM
1006201DB, 1006201VB, 1010207VB, 1011201DB, 1020201DB, 1020201VB, 1F10203VD, 1F10352VD, 1F13203FB
Back to top