895136 Mercury BOLT


895136 BOLT Mercury 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F15207DM, 1F15207FM, 1F15211HM BOLT
895136 BOLT Mercury
Rating:
88

Buy BOLT 895136 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$109.88

04-11-2024
0.36[0.16] pounds
US: Newparts
Genuine OEM Tire Pressure Monitoring System Sensor Transponder Transmitter for Mini R55 R56 R57 Cooper Base Clubman John Cooper Works S 2007-2009 1.6L L4 FWD
Newparts
Number on catalog scheme: 5
 

Mercury entire parts catalog list:

1A25203FK 2006
1A25203FL 2006
1A25311FK 2006
1A25312FK 2006
1A30413KZ 2010
1B08201DB 2005,2006
1F15207DM 2005
1F15207FM 2006
1F15211HM 2006,2008

Information:


At operating temperature, the hydraulic oil tank is hot and under pressure. Hot oil can cause burns. To prevent possible personal injury, release the pressure in the implement hydraulic circuits (boom, stick and bucket) before any hydraulic lines or components are disconnected or removed.
1. Release the pressure in the implement hydraulic circuits (boom, stick, and bucket) before any hydraulic lines or components are disconnected or removed as follows:a. Start the engine.b. Fully retract the stick cylinder rod.c. Adjust the position of the bucket so that it will be flat on the ground when the boom is lowered.d. Lower the boom until the bucket is flat on the ground.e. Shut off the engine, and place key in the "ON" position. Put the hydraulic activation control lever in the "UNLOCK" position.f. Move the control levers for boom, stick and swing to all full stroke positions. This will release any pressure that might be present in the pilot system.g. Return the key to "OFF" position.h. Slowly loosen the fill plug on the hydraulic tank, and release the pressure.i. Tighten the fill plug on the hydraulic tank to as torque of 68 7 N m (50 5 lb ft).j. The pressure in the hydraulic system has been released and lines and components can be removed.2. Drain the oil from the hydraulic oil tank into a suitable container for storage or disposal. The capacity of the hydraulic oil tank is 140 liters (37 U.S. gal). 3. Remove four bolts (1), the washers and support assembly (2).
Do not damage the hydraulic oil cooler core when the air conditioner condenser is being removed.
4. Remove four bolts (3) that hold air conditioner condenser (4) to the hydraulic oil cooler. Lay the air conditioner condenser out of the way of the hydraulic oil cooler. 5. Place a drain pan under the hydraulic oil cooler. Oil will flow from the hose connections when they are disconnected.6. Loosen two clamps (5) on hose assembly (6). Loosen two clamps (10) on hose assembly (11).7. Remove two clamps (8) and four bolts (9).8. Remove tube assemblies (7) and (12) from the hydraulic oil cooler. 9. Fasten a hoist to hydraulic oil cooler (14) as shown. Remove four bolts (13) that hold the hydraulic oil cooler in position. Remove the hydraulic oil cooler from the machine. The weight of the hydraulic oil cooler is 79 kg (175 lb). The following steps are for the installation of the hydraulic oil cooler.10. Check the condition of the hydraulic oil cooler prior to installation. Remove any dirt or debris that may restrict the flow of air through the core. If any of the cooling fins are bent, they should be straightened. 11. Fasten a hoist to hydraulic oil cooler (14) as shown. Carefully install the hydraulic oil cooler in the machine. Install four bolts (13) that hold it in position. 12. Install tube assemblies (7) and (12).13. Install two clamps (8) and four bolts (9).14. Tighten two clamps (10) on hose assembly (11).15. Tighten two clamps (5) on hose assembly (6). 16. Put air conditioner condenser (4) in position on the hydraulic oil cooler. Install four bolts (3) that hold it in position. 17. Install support assembly (2), the washers and four bolts (1).18. Fill the hydraulic oil tank with oil to the correct level. Refer to the Operation & Maintenance Manual for the correct filling procedure.End By:a. install hood assembly


Parts bolt Mercury:

16830
 
16830 BOLT, DRIVESHAFT HOUSING
1002201FM, 1002201JK, 1002201VB, 1003201NK, 1004137, 1004201JK, 1015203FL, 1015203YL, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1031207ZF, 1040203FL, 1040203YL,
823042 34
 
823042 34 BOLT
1002201FM, 1006201AK, 1006201FK, 1008201YM, 1015203FL, 1040203FL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F02201HM, 1F15207DM, 1F25A17DM
804367001
 
804367001 BOLT
1B08201DB
823042044
 
823042044 BOLT
1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1040203FL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F15207DM, 1F15207FM, 1F25A17DM
804367002
 
804367002 BOLT
1B08201DB, 1F02201HM
823042056
 
823042056 BOLT
1015203FL, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1F15207DM, 1F15207FM
879194293
 
879194293 BOLT
1F15211HM
898103132
 
898103132 BOLT
1F15211HM
Back to top