86580A 1 Mercury BOTTOM YOKE


86580A 1 BOTTOM YOKE Mercury 1115473WD, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1135473UD, 1135473VD, 1135473YD, 1135726, 1135D73CD, 1150413CD, 1150413SD, 1150413VD, 1150413WD, 1150413ZD, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 117 BOTTOM
86580A 1 BOTTOM YOKE Mercury
Rating:
48

Buy BOTTOM YOKE 86580A 1 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

Mercury entire parts catalog list:

1115473WD 2000
11354120D 1990,1991
1135412GD 1989
1135412MD 1992,1993,1994,1995
1135412SD 1996,1997,1998
1135412VD 1999
1135412WD 2000,2001,2002,2003,2004,2005
1135473UD 1998
1135473VD 1999
1135473YD 2001,2002,2003
1135726 1986,1987,1988
1135D73CD 2004,2005
1150413CD 2004,2005
1150413SD 1996,1997,1998
1150413VD 1999
1150413WD 2000,2001
1150413ZD 2002,2003
1150453BD 1988
1150453GD 1989
1150453JD 1990
1150625 1985
1150628 1978,1979,1980,1982,1983,1984,1985
1175412GD 1989
1175413LD 1991
1175413MD 1992,1993,1994,1995
1175626 1976,1977,1978,1979,1980,1985,1986,1988
1200412GD 1989,1990
1200413GD 1989,1990
1200628 1978,1979,1980,1982,1983,1984,1985,1986,1987,1988
1220727 1987,1988

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
B - Scotch Brite 1
C 1U-5718 Vacuum Pump 1
169-7372 Bottle Assembly 1
4C-4057 Clear Plastic Tubing
7.92 mm (0.312 inch) OD 1
4C-4055 Clear Plastic Tubing
6.35 mm (0.250 inch) OD
D 9U-5470 Reamer 1
E 4C-6161 Tube Brush 1
F 9U-6862 Tapered Brush 1
G 4C-6774 Vacuum Gun Kit 1
H 4C-5027 Tap Wrench 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Evacuate as much fuel and oil as possible from the cylinder head before installing the unit injector. Several evacuations may be necessary. Use Tooling (C) to remove the fuel and oil from the cylinder. Note: Tooling (F) is available to clean loose material from the sleeve bore and the cylinder.
Clean the carbon from the sleeve, the sleeve bore and the end of the unit injector. Clean the carbon from the seat area that is inside of the cylinder head. A fine grade of Tooling (B) is preferred. Clean the carbon from the cylinder head. If the sleeve of the unit injector has been removed from the engine, use Tooling (D) to remove only carbon from the surface of the sleeve. If the sleeve of the unit injector is installed in the engine, use Tooling (E) to clean the carbon deposit from the inside of the sleeve. The following procedure is the preferred method of cleaning the sleeve bore.Place a 38 mm (1.5 inch) square piece of Scotch Brite material on the end of Tooling (F). Twist Tooling (F) with Tooling (H) against the lower surface of the sleeve bore.The surface should be cleaned until the surface is smooth and shiny. The entire sleeve bore should be cleaned in order to remove any loose carbon particles.Note: Tooling (G) is available to clean loose material from the sleeve bore and the cylinder.
The correct procedures and tooling specifications must always be used. Failure to follow any of the procedures may result in damage, malfunction, or possible engine failure.
Illustration 1 g01355602Note: Replace the O-ring seals on the injector.
Install O-ring seal (9) and O-ring seal (10) on unit injector (4). Lubricate O-ring seal (9), O-ring seal (10), and the sleeve bore of the unit injector sparingly with clean engine oil.
Record the serial number for the injector and the injector confirmation code. When you install a new unit injector the E-Trim value must be programmed into the Engine Control Module. For more information, refer to Troubleshooting, "Injector Code - Calibrate".
Illustration 2 g01355632
Illustration 3 g01264293Note: Verify quill tube (1) is positioned out of the bore enough to see O-ring seal (2). This will ensure that the injector does not contact the quill tube during installation.
Place unit injector (4) into the bore. Make sure that the key (11) for the unit injector fits into slot (12) in the cylinder head.
Illustration 4 g01354952Note: Use new socket head bolt (7).
Position unit injector clamp (8) with the label "C9" in the up position. Install socket head bolt (7) into unit injector clamp (8). Tighten socket head bolt (7) to a torque of 28 3 N m (21 2 lb ft).
Illustration 5 g01356104
Position harness assembly (5) and install nuts (6).
Connect harness assembly (3) to unit injector (4).
Illustration 6 g01355441
Illustration 7 g01355608Note: Check the O-ring seal for wear or for damage. If necessary, replace the O-ring seal.
If the O-ring was damaged, perfo


Parts bottom Mercury:

9734T10
 
9734T10 BOTTOM COWL
1135726, 1175626
86580A 2
 
86580A 2 BOTTOM YOKE
11354120D, 1135412GD, 1135412MD, 1135412SD, 1135473UD, 1135726, 1150413SD, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1175413LD, 1175413MD, 1175626, 1200412GD, 1200628, 1220727
9744A18
9745A 7
9672A52
86580F 3
 
86580F 3 BOTTOM YOKE (TRACKER)
1135412MD, 1175413MD
828044A 1
 
828044A 1 BOTTOM COWL, Black
1135412SD, 1135412VD, 1135412WD, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413SD, 1150413VD, 1150413WD, 1150413ZD, 1150423FG, 1150423FY, 1150423HF, 1150423HG, 1150423HY, 1150424FY, 1150424HY, 1200413FY, 1200413HY, 1200423FG, 1200423FY, 1200423H
Back to top