16338 Mercury BRACKET, THROTTLE SHAFT


16338 BRACKET, THROTTLE SHAFT Mercury 1004137, 1004201FB, 1004201JK, 1004201VB, 1006201FK, 1B04201FB, 1F02201HM, 1F04201WB, 1F15207DM, 1F15207FM, 1F25A17DM BRACKET
16338 BRACKET, THROTTLE SHAFT Mercury
Rating:
73

Buy BRACKET, THROTTLE SHAFT 16338 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

Mercury entire parts catalog list:

1004137 1987,1988,1989
1004201FB 2006
1004201JK 1990,1991,1992,1993,1994,1995,1996,1997,1998
1004201VB 1999,2000,2001,2002,2003,2004,2005
1006201FK 2006
1B04201FB 2006
1F02201HM 2006
1F04201WB 2000,2001,2002,2003,2004,2005
1F15207DM 2005
1F15207FM 2006
1F25A17DM 2005

Information:

2. Remove the bolts, and remove damper guard (1) from the engine. 3. Remove bolts (4), and remove elbow (3) and tube (2) as a unit from the engine. 4. Remove bolts (5) that hold the water pump to the drive adapter. 5. Fasten a hoist to water pump (7), and remove bolts (6) to remove the water pump from the engine. The weight of water pump (7) is 27 kg (60 lb.).Install Water Pump
1. Make sure gasket (3) is in position on the water line adapter. Install O-ring seal (2) on the pump housing, and put clean engine oil on it.2. Fasten a hoist to water pump (1), and put it in position in the pump drive. Make sure the splines on the pump shaft are correctly engaged with the pump drive splines. 3. Install bolts (4) and (5) that hold the water pump to the water line adapter and the pump drive adapter. 4. Install O-ring seal (8) on the pump housing, and put clean engine oil on it.5. If necessary, make a replacement of the O-ring seals on each end of tube (6), and put clean engine oil on the seals.6. Put tube (6) and elbow (7) as a unit in position, and install the bolts to hold these in position. 7. Install damper guard (9) on the engine.8. Fill the cooling system with coolant to the correct level. See the Maintenance Manual.Disassemble Water Pump
Start By:a. remove water pump 1. Remove elbow (1) from housing assembly (2). Remove the O-ring seal from elbow (1). 2. Remove O-ring seal (5) from the back of housing assembly (2).3. Remove washer (4) that holds shaft assembly (3) in housing assembly (2). 4. Remove cover (6) from housing assembly (2). Remove the O-ring from cover (6). Later model water pumps use a nut to hold the impeller on the shaft instead of bolt (8).5. Loosen bolt (8) and the washer that hold impeller (7) to the pump shaft. Use tooling (A) to loosen impeller (7) from the end of the pump shaft. Remove tooling (A), bolt (8), the washer and impeller (7) from the pump shaft and housing assembly (2). 6. Remove spring (10) from seal assembly (9) and shaft assembly (3).7. Use a soft faced hammer and push shaft assembly (3) out of seal assembly (9) and housing assembly (2). Remove seal assembly (9) from housing assembly (2). 8. Remove ceramic seal (11) from the rubber ring. Remove the rubber ring from housing assembly (2). 9. Remove seal (12) from the back of housing assembly (2).Assemble Water Pump
1. If necessary, make a replacement of the two filters in the pump housing at location (1).2. If necessary, make a replacement of plug (2) and the seal.3. Use tool group (A) to install the seal in the housing assembly. Make sure the lip of the seal is toward the outside as shown. Put clean engine oil on the lip of the seal. 4. Install shaft assembly (3) in housing assembly (4). Install washer (5) and the bolts to hold shaft assembly (3) in position.
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
5. Put ceramic seal (6) in position in the rubber ring. Use hand pressure and the tool (which is with the replacement seal) to install the ceramic seal. 6. Remove the spring from seal assembly (7). Use hand pressure and the tool (which is with the replacement seal) to install the seal assembly. Push the seal assembly on the shaft until the seal faces make light contact. 7. Install spring (8) on the carbon seal assembly.8. Put impeller (9) in position on the pump shaft as shown. 9. Install washer (11) and bolt (10). Tighten bolt (10) to a torque of 90 15 N m (66 11 lb.ft.). Hit the bolt with a hammer, and tighten it again to a torque of 90 15 N m (66 11 lb.ft.). Later model water pumps use a nut on the shaft assembly instead of bolt (10). Tighten the nut to a torque of 200 25 N m (148 18 lb.ft.). 10. Make sure the studs for cover (12) are tightened to a torque of 27 4 N m (20 3 lb.ft.) in the pump housing.11. Put clean engine oil on O-ring seal (13), and install it on cover (12). Put cover (12) in position, and install the nuts to hold it to the pump housing. 12. Put clean engine oil on the O-ring seal, and install it in elbow (14). Put elbow (14) in position on housing assembly (4), and install the bolts to hold the unit together.13. Put clean engine oil on the O-ring seal, and install it on the back of housing assembly (4).End By:a. install water pump


Parts bracket Mercury:

803528
BRACKET
803528 BRACKET
1B04201FB, 1F02201HM, 1F04201WB
878350
BRACKET
878350 BRACKET
1B04201FB, 1F04201WB
878351
803590
BRACKET
803590 BRACKET
1B04201FB, 1F04201WB
803575
892779
BRACKET
892779 BRACKET
1B08201DB, 1F25A17DM
Back to top