62497 Mercury BRACKET, SUPPORT - DRIVE SHAFT(LONG SHAFT)


62497 BRACKET, SUPPORT - DRIVE SHAFT(LONG SHAFT) Mercury 1115503, 1115525, 1140528, 1150503, 1150538, 1150625 BRACKET
62497 BRACKET, SUPPORT - DRIVE SHAFT(LONG SHAFT) Mercury
Rating:
103

Buy BRACKET, SUPPORT - DRIVE SHAFT(LONG SHAFT) 62497 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 40
 

Compatible models:

Mercury entire parts catalog list:

1115503 1973,1974,1976,1977
1115525 1985
1140528 1978,1979
1150503 1973,1974,1975,1976,1977,1985
1150538 1978
1150625 1985

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     -     Strap Wrench     1    Start By:
Remove engine.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02786236
Use Tooling (A) in order to remove engine oil filter (5) . Remove plug (3) and drain the engine lubricating oil. Remove O-ring seal (4) (not shown) from plug (3) . Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for correct procedure.
Remove breather hose (1) from the clip. Position the breather hose away from the engine oil pan.
Loosen nut (6) and remove tube assembly (2) . Remove O-ring seal (7) and seal (8) from the tube assembly.
Illustration 2 g02786240
Remove nuts (9) and bolts (10) from engine oil pan (11) .Note: The bolts are different lengths. Note the position of the different bolts.
Attach a suitable lifting device to engine oil pan (11) . Support the weight of the engine oil pan. The engine oil pan weighs approximately 41 kg (90 lb).
Use the lifting device to remove engine oil pan (11) from the cylinder block.
Remove gasket (12) from the cylinder block.Installation Procedure
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
A     -     Loctite 5900     -    
B     -     Loctite 243     -    
C     -     Straight Edge     1    Note: In order to install a cast iron oil pan, the engine must be removed from the machine.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the face of the cylinder block is clean and free from damage. Inspect the studs in the cylinder block for damage. If necessary, replace the studs.
Ensure that the engine oil pan is clean and free from damage.
Illustration 3 g02786279
Illustration 4 g02786281
Apply a bead of Tooling (A) to Positions (Y) on the cylinder block.Note: If the bridge piece for the cylinder block has just been installed, the engine oil pan must be installed before Tooling (A) has cured.
Illustration 5 g02786286
Illustration 6 g02786316
Align a new gasket (12) with the studs in the cylinder block. Install the gasket to the cylinder block.
Attach a suitable lifting device to engine oil pan (11) . The engine oil pan weighs approximately 41 kg (90 lb).
Use the lifting device to align engine oil pan (11) with the studs in the cylinder block. Install the engine oil pan to the cylinder block. Remove the lifting device from the engine oil pan.
Install nuts (9) and bolts (10) finger tight.
Align the rear face of engine oil pan (11) to the rear face of cylinder block (13) on both sides. Use Tooling (C) and a feeler gauge in order to check the alignment between the engine oil pan and the cylinder block. The maximum step that is allowed between the cylinder block and the sump is 0.1 mm (0.004 inch).
Tighten bolts (9) and nuts (10) to a torque of 22 N m (16 lb ft). Refer to Specifications, "Engine Oil Pan" for t


Parts bracket Mercury:

52732
 
52732 BRACKET, ANCHOR - CONTROL CABLES SERIAL AND UP
1080500, 1080508, 1090520, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1650100, 1800100, 1850503, 1850506
55805
 
55805 BRACKET, STOP
1090528, 1115100, 1115503, 1115525, 1115528, 1135100, 1140528, 1150503, 1150538, 1150625, 1650100, 1800100, 1850503
59757
 
59757 BRACKET, RETAINER-HIGH TENSION LEAD
1115100, 1115503, 1115525, 1135100, 1150503, 1150625, 1500101, 1500205, 1650502, 1650503, 1800100, 1850503
74406
 
74406 BRACKET, MOUNTING - STARTER SOLENOID
1050200, 1070500, 1080500, 1090520, 1090528, 1115520, 1115523, 1115528, 1140520, 1140528, 1140629, 1150538
67245T
BRACKET
67245T BRACKET
1135726, 1150453BD, 1150625, 1150628, 1175626, 1200628, 1220727, 1250422GD
86386A 1
 
86386A 1 BRACKET ASSEMBLY
1135726, 1150453BD, 1150625, 1150628, 1175626, 1200628, 1220727, 1225620
88623A 1
 
88623A 1 BRACKET
1150625, 1150628, 1175626, 1200628
13990
 
13990 BRACKET
1035204, 1050200, 1060504, 1075524, 1090524, 1115525
Back to top