898101637 Mercury BUSHING


898101637 BUSHING Mercury 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ BUSHING
898101637 BUSHING Mercury
Rating:
98

Buy BUSHING 898101637 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$15.55
 

14-12-2023
0.0462[0.02] pounds
US: Boating Accessories
New Mercury Mercruiser Quicksilver OEM Part # 23-898101637 BUSHING
Quiksilver
Number on catalog scheme: 27
 

Compatible models:

Mercury entire parts catalog list:

1A25203FK 2006
1A25203FL 2006
1A25311FK 2006
1A25312FK 2006
1A30413KZ 2010

Information:

start by:a) remove mufflerb) remove fuel ratio controlc) remove fuel injection linesd) remove fuel transfer pumpe) remove fuel shutoff solenoid1. Put the fuel injection pump in correct timing with the engine as follows: a) Turn the engine flywheel with tool (A) to put No. 1 piston at top center compression stroke. b) Install tool (B) in the fuel ratio control opening to engage with the timing groove in the fuel injection pump camshaft. See FINDING TOP CENTER COMPRESSION POSITION FOR NO. 1 PISTON AND CAMSHAFT TIMING FOR THE FUEL INJECTION PUMP in TESTING AND ADJUSTING.2. Remove the cotter pin and pin (1) that hold governor control cable (3).3. Loosen the nut that holds cable (3) to the engine bracket and remove the cable from the bracket.4. Disconnect fuel lines (2) from the governor plate.5. Remove the vee belt set from the fan drive and disconnect the spring from the belt tightener.6. Remove the cover and gasket from the automatic timing advance housing. 7. Remove the four bolts and retainer (4) that hold the automatic timing advance to the fuel pump camshaft.
Do not let the retainer drop in the housing.
8. Remove brackets (5) and bolts (6) from each side of the fuel injection pump housing.9. Pull the fuel injection pump housing out of the timing gear housing.10. Install a 5/16"-18 NC forged eyebolt and a 3/8"-16 NC forged eyebolt in the fuel injection pump housing as shown. Fasten a hoist to the fuel injection pump housing and governor and remove it from the engine. Weight of the fuel injection pump housing and governor is 110 lb. (50 kg). 11. Inspect the two O-ring seals on the bottom and seal (7) on the front of the fuel injection pump housing. If the seals have damage, use new parts for replacement.
Do not cause damage to the oil inlet and outlet dowels on the bottom of the fuel injection pump housing.
Install Fuel Injection Pump Housing And Governor
Make sure there is no paint, dirt or foreign material on the machined surface of the fuel injection pump housing and the machined surface of the cylinder block. The surfaces must be clean before the fuel injection pump housing and the machined surface of the cylinder block. The surfaces must be clean before the fuel injection pump housing is installed.
1. Turn the fuel injection pump camshaft until tool (A) can be installed in the groove of the fuel injection pump camshaft.2. Put 5P960 Multipurpose Grease on the O-ring seals. Install the two seals on the bottom of the oil inlet and oil outlet dowels. Install the seal on the front of the housing.3. Fasten a hoist to the fuel injection pump housing and governor. Put the unit in position on the engine. Make sure the fuel injection pump housing is in the automatic timing advance unit and the bolt holes in the fuel injection pump housing are in alignment with the bolts holes in the engine. Install the bolts and brackets that hold the unit in position. Make sure the automatic timing advance unit is in correct position on the fuel pump camshaft.4. Install the retainer and the bolts that hold the automatic timing advance unit on the fuel pump camshaft. Tighten the bolts to a torque of 50 lb. ft. (70 N m) with the timing pin in the fuel pump camshaft.5. Remove the timing pin and tighten the bolts to a torque of 100 5 lb. ft. (135 7 N m) 6. Install the gasket and cover (1) for the automatic timing advance. 7. Put spring (3) in position on the belt tightener and install pin (4) and the cotter pin to hold it.8. Install vee belt set (2) for the fan drive. 9. Connect the governor control cable (6) to lever (5) with pin (8) and the cotter pin.10. Make sure governor control cable (6) is in position in the bracket and tighten nut (7).11. Connect the fuel lines to the governor plate.end by:a) install fuel shutoff solenoidb) install fuel transfer pumpc) install fuel injection linesd) install fuel ratio controle) install muffler


Parts bushing Mercury:

95361
 
95361 BUSHING, WATERTUBE (LOWER)
1002201FM, 1002201JK, 1002201VB, 1002204, 1003201NK, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
853743 5
 
853743 5 BUSHING
1015203FL, 1015203YL, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1031207ZF, 1040203FL, 1040203YL, 1040213YL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413K
16176 5
 
16176 5 BUSHING
1040203FL, 1040203YL, 1040213YL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
16176 4
 
16176 4 BUSHING
1040203FL, 1040203YL, 1040213YL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
16176009
 
16176009 BUSHING
1040203FL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F15211HM
16176007
BUSHING
16176007 BUSHING
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1F25A17DM
16176010
 
16176010 BUSHING
1040203FL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
898101646
 
898101646 BUSHING, Plastic
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
Back to top