88807A20 Mercury CABLE ASSEMBLY, COVER


88807A20 CABLE ASSEMBLY, COVER Mercury 1031203PD, 1031203UD, 1041312UB, 1150413SD, 1150413VD, 1150413WD, 1175413LD, 1175413MD, 1200413GD, 1220727 CABLE
88807A20 CABLE ASSEMBLY, COVER Mercury
Rating:
98

Buy CABLE ASSEMBLY, COVER 88807A20 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 34
 

Mercury entire parts catalog list:

1031203PD 1994,1995,1996,1997,1998,1999
1031203UD 1998,1999
1041312UB 1998
1150413SD 1996,1997,1998
1150413VD 1999
1150413WD 2000,2001
1175413LD 1991
1175413MD 1992,1993,1994,1995
1200413GD 1989,1990
1220727 1987,1988

Information:

1. Remove suction bell (3) and tubes, oil supply tube (2) and BrakeSaver oil supply tube (1) from the engine block and oil pump. 2. Remove three bolts (5) and oil pump (4) from the engine. The following steps are for installation of the oil pump.3. Put oil pump (4) in position on the engine. Make sure the oil pump gear is engaged with the crankshaft gear, and install three bolts (5) that hold the oil pump.4. Put clean engine oil on the O-ring seals on the oil tubes.5. Install suction bell (3) and tubes, oil supply tube (2) and the BrakeSaver oil supply tube (1).End By:a. install oil pan (BrakeSaver)Disassemble Oil Pump (BrakeSaver)
Start By:a. remove oil pump (BrakeSaver) 1. Remove the bolt and washer that hold drive gear (1) on the shaft.2. Use tooling (A) to remove drive gear (1) from the shaft. Remove the key from the shaft. Put alignment marks on the pump bodies so they can be assembled in the correct position. 3. Remove retainer (3) for the bypass valve. Remove the spring and bypass valve.4. Remove bolts (4) that hold pump body (2) to the main pump body. Remove pump body (2).5. Use tooling (B) to remove the bearings from pump body (2). 6. Remove gears (7). Put identification marks on the gears so they can be assembled in the same position.7. Remove spacer (6) from main oil pump body (5). Use tooling (B) to remove the bearings from spacer (6).8. Remove the gears from main oil pump body (5). 9. Use tooling (B) to remove the bearings from the main oil pump body.Assemble Oil Pump (BrakeSaver)
1. Use tooling (B) to install bearings (8) until they are even with the outside surface of main oil pump body (5). Install bearings (8) so the joints in the bearings are 30° 15° from the center line of the bearing bores and toward the oil pump outlet passage as shown. 2. Use tooling (B) to install bearings (9) in the spacer. Install the bearings until they are in position an equal distance in from each side of the pacer. Install the bearings with the oil holes in the bearings in alignment with the oil holes in the spacer and the joints in the bearings in alignment with the cavity on the spacer as shown. 3. Put clean engine oil on all the gears and bearings before they are assembled in the oil pump. Install idler and drive gears (10) in the main oil pump body.4. Install spacer (6) on the gear shafts with the smaller cavity out and the oil holes in the spacer toward the pump outlet passage as shown. 5. Use tooling (B) to install bearings (11) in pump body (2) until they are 1.52 0.25 mm (.060 .010 in.) from the inside edge of the bearing ores. Install the bearings so the joints in the bearings are 30° 15° from the center line of the bearing bores and toward the outlet passage. The outlet passage has a cavity between the bearing bores. 6. Install pump gears (7) on the oil pump shafts in their original position.7. Install pump body (2). Install bypass valve (12) spring (13) and retainer (3).8. Install the key on the shaft. 9. Install gear (1) on the shaft. Install the washer and bolt that hold the gear on the shaft. Be sure the pump turns freely after assembly.End By:a. install oil pump (BrakeSaver)


Parts cable Mercury:

816311
CABLE TIE, (8.00 Inches)
816311 CABLE TIE, (8.00 Inches)
1006201PD, 1006201RB, 1006206, 1006211RD, 1008211RD, 1015203YL, 1016207PD, 1016207RB, 1016207SB, 10202014D, 1020201BC, 1030201YL, 1031203PD, 1031203UD, 1031207ZF, 1035207, 1040203YL, 10402139D, 1040213YL, 1041312UB, 10432037D, 1050302SD, 1050312LD, 1
60466A20
 
60466A20 CABLE ASSEMBLY
1175413LD, 1175413MD, 1200413GD, 1220727
87895A 4
 
87895A 4 CABLE (175)
1150413SD, 1150413VD, 1175413LD, 1175413MD
88238A11
CABLE
88238A11 CABLE
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312FB, 1050411DD, 1050412DB, 1050412DD, 1050412F
88238A15
CABLE
88238A15 CABLE
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312FB, 1050411DD, 1050412DB, 1050412DD, 1050412F
43242 5
 
43242 5 CABLE-THROTTLE
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB
43242 7
 
43242 7 CABLE-THROTTLE
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB
88439A34
 
88439A34 CABLE ASSEMBLY, Positive - Battery
1135412WD, 1150413WD, 1250413UE, 1256413WD
Back to top