56011A 2 Mercury CHECK VALVE ASSEMBLY, LOWER END CAP


56011A 2 CHECK VALVE ASSEMBLY, LOWER END CAP Mercury 1020202, 1040102, 1075202, 1110102, 1115503, 1115525, 1150503, 1150625, 1200203, 1225620, 1402202, 1500101, 1650502, 1850503, 1850506 CHECK
56011A 2 CHECK VALVE ASSEMBLY, LOWER END CAP Mercury
Rating:
103

Buy CHECK VALVE ASSEMBLY, LOWER END CAP 56011A 2 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 27
 

Mercury entire parts catalog list:

1020202 1972
1040102 1972,1973,1974
1075202 1972,1973
1110102 1972,1973
1115503 1973,1974,1976,1977
1115525 1985
1150503 1973,1974,1975,1976,1977,1985
1150625 1985
1200203 1973,1974,1975,1976,1977
1225620 1980
1402202 1972,1973,1974
1500101 1971,1972,1973,1974
1650502 1972
1850503 1973,1974,1975
1850506 1976,1977

Information:


Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Note: Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for information on replacing the filter.
Turn the keyswitch to the "OFF" position.
Open the air purge screw for the fuel filter by three full turns. Do not remove the air purge screw.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Start the engine. The engine should start and the engine should run smoothly. If the engine does not start after 30 seconds, allow the starter motor to cool for two minutes before attempting to start the engine again. Note: You may use the hand priming pump (if equipped) for the fuel filter instead of starting the engine and running the engine.
While the engine is running, observe the air purge screw. When a small drop of fuel appears at the threads of the air purge screw, close and tighten the air purge screw. Note: There may be a noticeable change in the sound of the running engine when the air purge screw is tightened. The change in the sound of the engine is normal.Note: Failure to tighten all fittings could result in serious fuel leaks.
Clean any residual fuel from the engine components. The Engine Has Been Run Out of Fuel
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Turn the keyswitch to the "OFF" position.
Fill the fuel tank(s) with clean diesel fuel.
Bleed the air from the system by opening the fuel pressure regulator valve by two turns and another half turn. Note: Do not remove the regulating valve completely. Open the valve enough to allow the air that is trapped in the cylinder head to be purged from the fuel system.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Crank the engine for 30 seconds. Use a suitable container to catch the fuel while you crank the engine. Allow the starter motor to cool for two minutes. Note: You may use the hand priming pump (if equipped) for the fuel filter instead of cranking the engine.
Crank the engine for 30 seconds. Allow the starter motor to cool for two minutes.
Close and tighten the fuel pressure regulating valve.
Crank the engine for 30 seconds. Allow the starter motor to cool for two minutes.
Repeat Step 7 until the engine starts and the engine runs. Note: Failure to tighten all fittings could result in serious fuel leaks.
Clean any residual fuel from the engine components. The Engine Has Been Rebuilt
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Turn the keyswitch to the "OFF" position.
Fill the fuel tank(s) with clean diesel fuel.
Open the air purge screw for the fuel filter by three full turns. Do not remove the air purge screw.
Bleed the air from the system by opening the fuel pressure regulator valve by two turns and another half turn. Note: Do not remove the regulating valve completely. Open the valve enough to allow the air that is trapped in the cylinder head to be purged from the fuel system.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Crank the engine for 30 seconds. Use a suitable container to catch the fuel while you crank the engine. Allow the starter motor to cool for two minutes. Note: You may use the hand priming pump (if equipped) for the fuel filter instead of cranking the engine.
Crank the engine for 30 seconds. Allow the starter motor to cool for two minutes.
Close and tighten the air purge screw.
Crank the engine for 30 seconds. Allow the starter motor to cool for two minutes.
Close and tighten the fuel pressure regulating valve. Note: Failure to tighten all fittings could result in serious fuel leaks.
Crank the engine for 30 seconds. Allow the starter motor to cool for two minutes.
Repeat Step 10 until the engine starts and runs.
Clean any residual fuel from the engine components.


Parts check Mercury:

28481A 1
 
28481A 1 CHECK VALVE 40
1020100, 1040100, 1075101, 1110100, 1115100, 1135100, 1500100, 1500101, 1650100, 1800100
30430A 2
 
30430A 2 CHECK VALVE ASSEMBLY
1020100, 1020202, 1040100, 1040102, 1045205, 1075101, 1075202, 1110100, 1110102
30430A 3
 
30430A 3 CHECK VALVE ASSEMBLY
1040208, 1115100, 1115503, 1115525, 1135100, 1150503, 1150625, 1400100, 1402202, 1402205, 1650502, 1650503, 1650506, 1800100
30430A 1
 
30430A 1 CHECK VALVE ASSEMBLY
1500100, 1500101, 1500205, 1800100
62365A 1
 
62365A 1 CHECK VALVE ASSEMBLY, BLEED HOSE
1115100, 1500101, 1800100
30430A11
 
30430A11 CHECK VALVE KIT
1200628, 1225620
16615
 
16615 CHECK VALVE KIT
1035204, 1035207, 1045217, 1050200, 1050312BC, 1060504, 1075524, 1090524, 1115525
Back to top