16200 Mercury CLAMP SCREW ASSEMBLY


16200 CLAMP SCREW ASSEMBLY Mercury 1002201FM, 1002201JK, 1002201VB, 1003201NK, 1004137, 1004201FB, 1004201JK, 1004201VB, 1006201AK, 1006201FK, 1008201YM, 1B04201FB, 1F04201WB CLAMP
16200 CLAMP SCREW ASSEMBLY Mercury
Rating:
98

Buy CLAMP SCREW ASSEMBLY 16200 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 24
 

Mercury entire parts catalog list:

1002201FM 2006
1002201JK 1990,1991,1992,1993,1994,1995,1996,1997,1998
1002201VB 1999,2000,2001,2002,2003,2004,2005
1003201NK 1993,1994,1996,1997,1998
1004137 1987,1988,1989
1004201FB 2006
1004201JK 1990,1991,1992,1993,1994,1995,1996,1997,1998
1004201VB 1999,2000,2001,2002,2003,2004,2005
1006201AK 2003,2004
1006201FK 2006
1008201YM 2001,2002,2003,2004
1B04201FB 2006
1F04201WB 2000,2001,2002,2003,2004,2005

Information:

1. Disconnect connector (1). 2. Attach Tool (A) and fasten a hoist.3. Remove four bolts (3) and stack (2). The weight of the stack and hardware is 45 kg (99 lb). 4. Remove hose clamp (6).5. Remove five bolts (5) and support (4).6. Repeat Steps 4 and 5 for the other side of the engine. 7. Remove six bolts (7) that connect oil pan (8) to flywheel housing (9). Loosen the rest of the bolts that hold the oil pan in position. 8. Attach Tool (A) to the flywheel housing and a hoist. 9. Lift the end of the engine enough so a 1/2 ( in) Hardened Washer (10) can be installed on each side of the engine between the oil pan and the cylinder block.10. Install blocks under the oil pan to support the engine when the flywheel housing is removed. Lower the engine onto the blocks. 11. Remove twenty one bolts (11) and flywheel housing (9). The weight of the flywheel housing is approximately 91 kg (201 lb).Install Flywheel Housing
1. Install two 1/2 in-13 NC × 101 mm (4 in) Long Guide Bolts in the cylinder block. Make sure gasket (12) is in position. The cylinder block, both sides of gasket (12) and the surface of the flywheel housing that makes contact with the gasket must not have any oil, fuel, water or gasket adhesive on them when the flywheel housing is installed on the engine.2. Install Tool (A) on the flywheel housing. Install flywheel housing (9) on the engine. The weight of the flywheel housing is approximately 91 kg (201 lb). Leave Tool (A) attached.
Torque Sequence Put 9S-3263 Thread Lock on bolts (17) through (20) before installation.3. Install the bolts that hold the flywheel housing in place.4. Use the following procedure to tighten the bolts: a. Tighten bolts 1 through 20 in number sequence to a torque of 40 10 N m (30 7 lb ft).b. Tighten the 3/8" bolts in number sequence to a torque of 55 10 N m (41 7 lb ft). Tighten the 1/2" bolts in number sequence to a torque of 135 20 N m (100 15 lb ft). If a new gasket is installed, cut the ends of the gasket so it is even with the bottom of the cylinder block.5. Use Tool (A) and a hoist to lift the flywheel housing and engine enough so that the washers between the oil pan and the cylinder block can be removed. 6. Tighten the bolts that hold the oil pan to the cylinder block. Install six bolts (7) that hold oil pan (8) to flywheel housing (9). 7. Install support (4) with five bolts (5). Install clamp (6) to a torque of 7.0 1.5 N m (5 1 lb ft).8. Repeat Step (7) for the other side of the engine. 9. Use Tool (A) to lift stack (2) in place. Install the stack to the engine with four bolts (3). 10. Connect connector (1).End By:a. install crankshaft rear seal and wear sleeveb. install all turbochargers


Parts clamp Mercury:

95306
 
95306 CLAMP, LEAD WIRE
1002201JK, 1002204, 1003201NK, 1004137, 1004201JK, 1006201FK, 1015203FL, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1040203FL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1
16060
 
16060 CLAMP, ALTERNATOR
1004137, 1004201FB, 1004201JK, 1004201VB, 1B04201FB, 1F04201WB
813275
CLAMP, RECTIFIER (SAIL POWER)
813275 CLAMP, RECTIFIER (SAIL POWER)
1002201FM, 1002201VB, 1004137, 1004201FB, 1004201JK, 1004201VB, 1006201AK, 1006201FK, 1008201YM, 1015203FL, 1015203YL, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL,
9623 1
 
9623 1 CLAMP BRACKET
1004201FB, 1004201JK, 1004201VB, 1006201AK, 1006201FK, 1008201YM, 1B04201FB, 1F04201WB
815031 1
815044
CLAMP
815044 CLAMP
1004201JK, 1004201VB, 1015203YL
Back to top