804039T02 Mercury CLAMP BRACKET, Port


804039T02 CLAMP BRACKET, Port Mercury 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ CLAMP
804039T02 CLAMP BRACKET, Port Mercury
Rating:
78

Buy CLAMP BRACKET, Port 804039T02 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Compatible models:

Mercury entire parts catalog list:

Information:

START BY:a. remove oil pump 1. Check each main bearing cap (2) for its location on the engine. Each cap has an arrow (1) to show the front of the block and a number (3) which gives the location of that cap.2. Remove No. 2 through No. 4 main bearing caps from the engine. Remove the lower bearings from the caps.3. Remove the thrust plate from each side of the No. 3 upper main bearing. 4. Turn the crankshaft until tool (A) can be installed in oil hole (4). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
Install the connecting rod bearings dry when the clearance checks are made. Put clean oil on the connecting rod bearings for final assembly. 5. Install lower bearings in the bearing caps.6. Install upper bearings in the cylinder block with tool (A). Be sure tab (5) on the back of the bearings fits in the groove of the caps and cylinder block. When the bearing clearance is checked, the crankshaft will have to be lifted up against the upper halves of the main bearings and held to get a measurement with Plastigage (B). The Plastigage will not hold the weight of the crankshaft. See the topic Install Crankshaft for service tips on the use of Plastigage (B).7. Check the bearing clearance with tool (B) as follows:a. Put tool (B) in position on the surface of the lower main bearing. do not turn the crankshaft when Plastigage (B) is in position.b. Put 2P2506 Thread Lubricant on the threads of the cap bolts. Install the caps and cap bolts, finger tight.c. Tighten the bolts on the tab end of the caps first to a torque of 260 14 N m (190 10 lb.ft.).
Do not use an impact wrench to tighten the bolts the additional 120°.
d. Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120° more. Make sure the main bearing caps are installed with their identification number (7) in alignment with the identification number on the left side of the cylinder block and arrow (6) toward the front of the block.8. Remove the main bearing caps and tool (B).9. Measure the thickness of the Plastigage to determine the bearing clearance. The clearance for new bearings must be 0.091 to 0.186 mm (.0036 to .0073 in.). the maximum clearance for used bearings is 0.25 mm (.010 in.).10. Install a thrust plate (8) on each side of the No. 3 upper bearing. Install the thrust plates with the side marked "BLOCK SIDE" toward the cylinder block.11. Install No. 2 through No. 4 main bearing caps.Follow the procedure in Step 7 to tighten the bolts.12. Do Steps 2, 4 through 9 and 11 for the No. 1 and No. 5 main bearings. 13. Check the end play of the crankshaft with tool (C). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.152 to 0.508 mm (0.006 to 0.020 in.). The maximum end play with used thrust plates is 0.89 mm (0.035 in.).END BY:a. install oil pump


Parts clamp Mercury:

17169
 
17169 CLAMP, STOP SWITCH
1004137, 1004201JK, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1031207ZF, 1040203FL, 1040203YL, 1040213YL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ,
16263 5
 
16263 5 CLAMP SCREW
1040203FL, 1040203YL, 1040213YL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F15211HM
898101T26
CLAMP BRACKET, Starboard, 14MM Thread
898101T26 CLAMP BRACKET, Starboard, 14MM Thread
1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
898101T25
CLAMP BRACKET, Port, 14MM Thread
898101T25 CLAMP BRACKET, Port, 14MM Thread
1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
898101231
 
898101231 CLAMP
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
898101237
 
898101237 CLAMP, (16.8)
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
856880002
 
856880002 CLAMP
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
804830002
 
804830002 CLAMP
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
Back to top