93192 Mercury CLAMP, LOWER MOUNT


93192 CLAMP, LOWER MOUNT Mercury 1050302SD, 1050312LD, 1055207DB, 1055207UD, 1055207VB, 1070312BC, 1070717, 1075217PD, 1075217VD, 10754120D, 1100312BD, 1100412PD, 1100412VB CLAMP
93192 CLAMP, LOWER MOUNT Mercury
Rating:
23

Buy CLAMP, LOWER MOUNT 93192 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

Mercury entire parts catalog list:

1050302SD 1996,1997
1050312LD 1991,1992,1993,1994,1995,1996
1055207DB 2005,2006
1055207UD 1998
1055207VB 1999,2000,2001,2002,2003,2004
1070312BC 1988,1989,1990
1070717 1987
1075217PD 1994,1995,1996,1997,1998
1075217VD 1999,2000,2001,2002,2003,2004
10754120D 1990,1991,1992,1993
1100312BD 1988,1989,1990,1991,1992,1993
1100412PD 1994,1995,1996,1997,1998
1100412VB 1999,2000,2001,2002,2003,2004

Information:

Start By:a. remove turbocharger 1. Install the turbocharger on tool (A) as shown.2. Put alignment marks on three housings of the turbocharger for correct alignment during assembly. Loosen clamp (2), and remove the clamp and housing (1) from housing assembly (3). 3. Loosen clamp (4), and remove housing assembly (3) from housing (5). 4. Put the cartridge group in position in tool (B) as shown.
When the nut is loosened, do not put a side force on the shaft. This can result in a bent shaft.
5. Use a 5S9566 Sliding T-Wrench and a universal socket (6) to remove the nut that holds the compressor wheel to the wheel assembly.6. Remove compressor wheel (7) and the shims from wheel assembly (8).7. Remove housing assembly (3) from wheel assembly (8). 8. Remove ring (9) and backplate (10) from wheel assembly (8). 9. Use tool (C), and remove snap ring (11) from housing assembly (3). 10. Remove insert (12) and sleeve (13) from housing assembly (3). 11. Remove ring (14) from sleeve (13). 12. Remove two screws (15) and deflector (16) from housing assembly (3). 13. Remove ring (18) and bearing assembly (17) from the housing assembly. 14. Remove sleeve (19) and ring (20) from the housing assembly. 15. Remove O-ring seal (23) from the housing assembly.16. Use tool (D), and remove snap ring (22) from the housing assembly.17. Remove bearing (21). Remove the snap ring behind the bearing with tool (D). 18. Use tool (D), and remove snap ring (25) from the housing assembly.19. Remove bearing (24). Remove the snap ring behind the bearing with tool (D).20. Check all the parts of the turbocharger for damage. If the parts are damaged, use new parts for replacement. See Special Instruction, Form No. SMHS6854 for Turbocharger Reconditioning. Also see Guidelines For Reusable Parts, Form No. SEBF8018.Assemble Turbocharger (Schwitzer S4A)
1. Make sure that all of the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material. Do not put oil on any parts of the turbocharger until after the compressor wheel has been installed. After the turbocharger has been assembled, pour clean engine oil into the oil inlet of the turbocharger.
Make sure that the snap rings that hold bearings (24) and (21) in position in housing assembly (3) are installed with the round edge of the outside diameter toward the bearing.
2. Install the snap ring behind bearing (24) with tool (D).3. Install bearing (24) in housing assembly (3).4. Use tool (D), and install snap ring (25) in the housing assembly. 5. Install the snap ring behind bearing (21) with tool (D).6. Install bearing (21) in the housing assembly.7. Use tool (D), and install snap ring (22) in the housing assembly. 8. Put wheel assembly (8) in position on tool (B) as shown.9. Put backplate (10) in position on the wheel assembly. Put 6V2055 High Vacuum Grease in the groove for seal ring (9) at assembly to one half or more of the depth of the groove all the way around.10. Install ring (9) in the groove in wheel assembly (8). 11. Put housing assembly (3) in position on wheel assembly (8). 12. Install ring (20) and sleeve (13) on the wheel assembly. 13. Make sure the screen is in place in bearing assembly (17). 14. Install bearing assembly (17) over the sleeve. Make sure the screen in the bearing assembly is facing down when it is installed.15. Put ring (18) in position on bearing assembly (17). 16. Put deflector (16) in position in the housing assembly, and install two screws (15). Tighten screws (15) to a torque of 2.25 .25 N m (20 2 lb.in.). Put 6V2055 High Vacuum Grease in the groove of sleeve (13) to one half or more of the depth of the grooves all the way around.17. Install ring (14) in the groove in sleeve (14). 18. Put sleeve (13) in position in insert (12). Install the insert and sleeve (13) as an assembly. 19. Use tool (C), and install snap ring (11) to hold insert (12) in place. 20. Put wheel (7) in position in compressor housing (1). Center the wheel in the compressor housing.21. Use a straight edge and a depth micrometer (26) and measure the distance between the wheel seating face and the compressor housing mounting face (dimension X) in four places. Find the average of the measurements. 22. Use a depth micrometer (26) to measure the distance between the surface of housing assembly (3) and the surface of sleeve (13) (dimension Y).23. Use a depth micrometer (26), and measure the distance between the surface of housing assembly (8) and the compressor housing mounting face (dimension Z).24. Calculate the necessary shim thickness as follows: The shims must be of uniform thickness and free of burrs and other imperfections. The total shim thickness should be 0.13 mm to 0.41 mm (.005 to .016 in.) and consist of one or two shims.25. Install wheel (7) at room temperature as follows:a. Put the correct amount of shims and wheel (7) in position on the wheel assembly.b. Put a small amount of clean engine oil on the threads of the wheel assembly.
Do not put a side force on the shaft when the nut that holds the compressor wheel in position is tightened.
c. Install the nut that holds wheel (7) in place. Tighten the nut to a torque of 14 to 17 N m (125 to 150 lb.in.).d. Remove the nut, and put 6V1541 Quick Cure Primer on the threads of the wheel assembly.e. Put 9S3265 Retaining Compound on the threads of the wheel assembly, and install the nut. Tighten the nut to a torque of 4 N m (35 lb.in.).f. Tighten the nut an additonal 90°. 26. Install housing (5) on tool (A) as shown.27. Put housing assembly (3) in its original position in housing (5), and install clamp.28. Tighten clamp (4) to a torque of 14 3 N m (10 2 lb.ft.). Tap the clamp lightly all the way


Parts clamp Mercury:

22875
 
22875 CLAMP, VENT HOSE
1035207, 1045217, 1050312BC, 1070312BC, 1070717, 1075217PD, 10754120D, 1075524, 1100312BD, 1100412PD, 1115100, 1115503, 1115525, 1135100, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135726, 1150413WD, 1150453BD, 1150453GD, 1150453JD, 1150503, 115062
47483
 
47483 CLAMP, TELL TALE HOSE TO EXHAUST MANIFOLD COVER
1035204, 1035207, 1050312BC, 1070312BC, 1070717, 10754120D, 1075524, 1080500, 1080508, 1090524, 1115525, 11354120D, 1135412GD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1175413LD, 1175626, 1200412GD, 1200413GD, 1200628, 1220727, 1225620, 125
63300 1
 
63300 1 CLAMP
1031203PD, 1031203UD, 1041312UB, 10432037D, 1045217, 1050302SD, 1050312LD, 1055207UD, 1115473WD, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1175412GD, 1175626, 1200412GD, 1200628, 1250422GD, 1B25203ZB
15279
 
15279 CLAMP
10402139D, 1070312BC, 1070717, 1135726, 1150453BD, 1150453GD, 1150453JD, 1175412GD, 1175626
99019
 
99019 CLAMP, WATER TUBE SEAL
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050302SD, 1050312FB, 1050312LD, 1050411DD, 1050412D
822867F 2
 
822867F 2 CLAMP BRACKET
10402139D, 1050302SD, 1050312LD, 1055207UD
826115
CLAMP
826115 CLAMP
1031203PD, 1031203UD, 1041312UB, 1075217PD, 1100412PD
834813
 
834813 CLAMP
1075217DD, 1075217FD, 1075217PD, 1075217VD, 10752L7DF, 10752L7FF, 1075317DB, 1075317FB, 1075412DB, 1075412DD, 1075412DN, 1075412FB, 1075412FY, 1090412DB, 1090412DC, 1090412DD, 1090412DN, 1090412DY, 1090412FF, 1090412FY, 1090422DY, 1090422FF, 1090472D
Back to top