23568 Mercury CLIP, SOLENOID LEAD AND HARNESS TO FRONT SUPPORT BRACKET


23568 CLIP, SOLENOID LEAD AND HARNESS TO FRONT SUPPORT BRACKET Mercury 1007208, 1010208, 1018200, 1025200, 1500100, 1500101, 1500205 CLIP
23568 CLIP, SOLENOID LEAD AND HARNESS TO FRONT SUPPORT BRACKET Mercury
Rating:
8

Buy CLIP, SOLENOID LEAD AND HARNESS TO FRONT SUPPORT BRACKET 23568 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Compatible models:

Mercury entire parts catalog list:

1007208 1978
1010208 1978
1018200 1980,1982,1983
1025200 1980,1982,1983
1500100 1970
1500101 1971,1972,1973,1974
1500205 1975

Information:


Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Drain the engine oil into a suitable container for storage or disposal.
Illustration 1 g00516290
Typical example
Remove bolts (2) and the washers. Remove sound suppression cover (1), if equipped.
Illustration 2 g01022237
Typical example
Remove the following items from the cylinder block: bolts (5), the washers, the isolators and the isolator sleeves.
Remove engine oil pan (6) and the gasket.
Remove pipe plug (3) and drain plug (4) with the O-ring seal, if necessary.Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     -         -    
(-) Loctite 5900     -    
B     -     Loctite 243     -    
C     -     Loctite 243     -    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Inspect the condition of the gasket. Replace the gasket, if necessary.
Clean the mating surface of the engine oil pan and the cylinder block.Note: Apply Tooling (A) to the edges of the cylinder block and to the seams prior to installation.
Illustration 3 g01022237
Typical example
Place the gasket and engine oil pan (6) on the cylinder block.
Install the following items: isolator sleeves, isolators, bolts (5), and the washers.Note: Perform the following procedure in order to eliminate the possibility of an oil leak from the bolt for the engine oil pan:
Illustration 4 g01022239
Note: The path of the oil leak is through the threads of bolt (8) for the engine oil pan. The third bolt from the front of engine block (7) on the right side of the engine is the suspect bolt.
Clean the bolt hole and dry the bolt hole.
Clean the oil pan bolt and dry the oil pan bolt.
Apply Tooling (B) or Tooling (C) to the threads of the bolt.
Install the oil pan bolt and tighten the bolt to a torque of 55 10 N m (40 7 lb ft).
Wipe off excess Tooling (A) from all gasket joints. Use a flat, straight tool in order to remove the sealant.
Apply Tooling (C) to pipe plug (3). Install pipe plug (3). Tighten the plug to a torque of 80 11 N m (60 8 lb ft).
Install drain plug (4) and the O-ring seal. Tighten the plug to a torque of 70 15 N m (50 11 lb ft).
Illustration 5 g00516290
Typical example
Position the sound suppression cover (1) on the engine oil pan and install six bolts (2) with the washers.
Fill the engine with oil to the correct level. See the Operation and Maintenance Manual for the correct filling procedure.


Parts clip Mercury:

30954
 
30954 CLIP
1003203, 1006201DB, 1006201PD, 1006201RB, 1006201VB, 1006206, 1006211RD, 1007208, 1008211RD, 1010207VB, 1010208, 1011201DB, 1016207PD, 1016207RB, 1016207SB, 1018200, 1018204, 10202014D, 1020201BC, 1020201DB, 1020201VB, 1025200, 1040100, 1040102, 1045
26550
 
26550 CLIP
1020100, 1040100, 1040208, 10402139D, 1050302SD, 1050312LD, 1075101, 1110100, 111047JHD, 1115100, 1115473WD, 1135100, 1135412MD, 1135412VD, 1135412WD, 1135473UD, 1135473VD, 1135473YD, 1135D73CD, 1135D73FT, 1150413CD, 1150413FY, 1150413HF, 1150413HY,
24836
 
24836 CLIP
1018200, 1018204, 1020201BC, 1020201DB, 1020201VB, 1025200, 1040100, 1075101, 1400100, 1500100, 1A30302ZB, 1A40302FD, 1A40302HZ, 1A40303KZ, 1A40311FZ, 1A40311HZ, 1A40403HZ, 1A40412HZ, 1A41412ZB, 1A41452EZ, 1A41452FU, 1A51411HZ, 1A51412HZ, 1A51452EZ,
29641
 
29641 CLIP, RETAINING - SHIFT SHAFT
1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050302SD, 1050312BC, 1050312LD, 1055207DB, 1055207UD, 1055207VB, 1060504, 1070312BC, 1070500, 1070717, 1075217DD, 1075217FD, 1075217PD, 1075217VD, 10752L7DF, 10752L7FF, 1075317DB, 1075
52905
 
52905 CLIP, HIGH TENSION LEAD
1080508, 1500100, 1500101, 1500205, 1850506
46379
 
46379 CLIP, STATOR LEAD TO CRANKCASE
1500100, 1500101, 1500205
20233
Back to top