6120A 1 Mercury COIL ASSEMBLY (1 3/4" AND 3 1/2" LEADS)


6120A 1 COIL ASSEMBLY (1 3/4" AND 3 1/2" LEADS) Mercury 1007208, 1007209, 1010208, 1020208, 1075204, 1110204, 1200203 COIL

Buy COIL ASSEMBLY (1 3/4" AND 3 1/2" LEADS) 6120A 1 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Compatible models:

Mercury entire parts catalog list:

1007208 1978
1007209 1979,1980,1981,1982,1983,1984,1985
1010208 1978
1020208 1978,1979,1980
1075204 1974,1975,1976,1977
1110204 1974,1975,1976,1977
1200203 1973,1974,1975,1976,1977

Information:

Probable Causes
Diagnostic codes
Electrical connectors
ECM connection
Fuel system inspection
Air inlet and exhaust systemRecommended Actions
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 1
Troubleshooting Test Steps Values Results
1. Diagnostic Codes
A. Establish communication between the electronic service tool and the Electronic Control Module (ECM). Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Use the electronic service tool to check for active diagnostic codes.
Diagnostic codes
Result: There are active or logged codes.
Repair: Troubleshoot any codes before continuing with this procedure. Refer to Troubleshooting, "Diagnostic Trouble Codes".
Result: There are no active or logged codes.
Proceed to Test Step 2.
2. Electrical Connectors
A. Check all electrical connectors for damage. Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Make sure that all the connector seals are in place and that the connectors have been correctly installed.
Electrical connectors
Result: An electrical connector is damaged.
Repair: Repair the electrical connector or replace the electrical connector.
Result: A connector seal is displaced or missing or an electrical connector is not correctly installed.
Repair: Repair the electrical connector or replace the electrical connector.
Result: All electrical connectors are OK.
Proceed to Test Step 3.
3. ECM Connection
A. Check that the P2/J2 and P1/J1 connectors are correctly installed.
Note: If a fault is suspected with the ECM power or ground connections, refer to Troubleshooting, "Electrical Power Supply - Test".
ECM connection
Result: An ECM connector is not correctly installed.
Repair: Repair the electrical connector or replace the electrical connector.
Result: Both ECM connectors are correctly installed.
Proceed to Test Step 4.
4. Fuel System Inspection
A. Check that the fuel shut-off valve is in the OPEN position.
B. If the temperature is below 0 °C (32 °F), check for solidified fuel (wax).
C. Check for fuel supply lines that are restricted.
D. Check that the low-pressure fuel lines are correctly installed.
E. Check the pressures in the fuel system. Refer to Systems Operation, Testing, and Adjusting, "Fuel System Pressure - Test"
F. Check the diesel fuel for contamination. Refer to Systems Operation, Testing, and Adjusting, "Fuel Quality - Test".
G. Check for air in the fuel system. Refer to Systems Operation, Testing, and Adjusting, "Air in Fuel - Test".
H. Ensure that the fuel system has been primed. Refer to Systems Operation, Testing, and Adjusting, "Fuel System - Prime".
Fuel System
Result: A defect was found in the fuel system.
Repair: Make any necessary repairs.
Result: No defects found.
Proceed to Test Step 5.
5. Fuel Filters
A. Replace the primary fuel filter and the secondary fuel filter. Refer to the Operation and Maintenance Manual, "Fuel System Primary Filter (Water Separator) Element - Replace".
B. Run the engine in the conditions that the fault occurred.
Fault cleared
Result: The fault has been rectified.
Return the engine to service.
Result: The fault is still present.
Proceed to Test Step 6.
6. Air Inlet and Exhaust System
A. Check the air filter restriction indicator.
B. Ensure that the air filter is clean and serviceable
C. Check the air intake and exhaust systems for the following defects:
Blockages
Restrictions
Damage to lines or hoses
Defects
Result: A defect was found in the air intake or exhaust system.
Repair: Make any necessary repairs.
Result: No defects found in the air intake or exhaust systems.
Contact the Dealer Solution Network (DSN).


Parts coil Mercury:

4992A 1
4991A 1
5288A 2
COIL ASSEMBLY, IGNITION
5288A 2 COIL ASSEMBLY, IGNITION
1004200, 1007209, 1040200, 1040206, 1075204, 1110204, 1150625, 1150628, 1175626, 1200203, 1200628, 1402205
5748A 2
 
5748A 2 COIL ASSEMBLY,IGNITION
1010208, 1020208, 1040208, 1075204, 1080508, 1110204, 1200203, 1402205, 1500206, 1650506, 1700507, 1850506
6119A 1
 
6119A 1 COIL ASSEMBLY (5 1/2" AND 6 3/8" LEADS)
1007208, 1007209, 1010208, 1020208, 1075204, 1110204, 1200203
5589A 1
 
5589A 1 COIL ASSEMBLY (2 1/4" AND 4 1/4" LEADS)
1004200, 1040206, 1075204, 1110204
Back to top