835387 Mercury COIL, Lighting


835387 COIL, Lighting Mercury 1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD COIL
835387 COIL, Lighting Mercury
Rating:
18

Buy COIL, Lighting 835387 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$99.67
 

21-08-2022
0.2182[0.10] Pounds
-: -
MERCURY COIL-LIGHT
Mercury || 835387 || Used, no corrosion, tested and works well || 1999-2006 || 9.9hp
Number on catalog scheme: 6
 

Compatible models:

Mercury entire parts catalog list:

1F10203VD 1999,2000,2001,2002,2003,2004,2005
1F10352VD 1999
1F13203FB 2006
1F15201UD 1998

Information:


Illustration 1 g01386933
Typical schematic
Illustration 2 g01381785
P1 ECM connector
(P1-34) CAN data link −
(P1-42) Shield for the CAN data link
(P1-50) CAN data link +
Illustration 3 g01381831
Customer connector
(Terminal 32) CAN data link −
(Terminal 33) Shield for the CAN data link
(Terminal 35) CAN data link +
Illustration 4 g01381854
Service tool connector
(Terminal C) Shield for the CAN data link
(Terminal F) CAN data link −
(Terminal G) CAN data link +
Illustration 5 g01234146
Location of ECM connectors
Test Step 1. Inspect the Electrical Connectors and the Wiring
Turn the main disconnect switch to the OFF position.
Thoroughly inspect the ECM connector J1/P1. Inspect all of the connectors to other modules on the CAN data link. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and the wiring for abrasion and for pinch points. Expected Result:All of the connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and connectors appear to be OK. Proceed to Test Step 3.
Not OK - The connectors and/or wiring are not OK.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Verify the Proper Installation of the Terminating Resistors
Verify that the terminating resistors are installed on the ends of the data link.
Disconnect the J1/P1 ECM connector and measure the resistance between P1-50 (CAN data link +) and P1-34 (CAN data link -). Expected Result:The resistance is approximately 60 3 Ohms.Results:
OK - The resistance is within the range. Proceed to Test Step 3.
Not OK - The resistance is approximately 120 6 Ohms. A terminating resistor is missing or damaged.Repair: If a termination resistor is missing, install the missing resistor. If both resistors are present, measure the resistance between pin A and pin B of the termination resistor. The resistance should measure 120 3 Ohms. Replace the termination resistor if the resistance is not 120 3 Ohms.STOPTest Step 3. Check for Shorts in the Harness
Disconnect the ECM connector J1/P1 at the engine ECM.
Disconnect the ECM connector J2/P2 at the engine ECM.
Disconnect any control modules from the CAN data link.
Disconnect Caterpillar Electronic Technician (ET) from the service tool connector.
Measure the resistance from P1-50 to every terminal on ECM connectors P1 and P2.
Measure the resistance from P1-50 to the chassis ground.
Measure the resistance from P1-34 to every terminal on ECM connectors P1 and P2.
Measure the resistance from P1-34 to the chassis ground. Expected Result:The resistance measurements indicate an open circuit.Results:
OK - The resistance measurements indicate an open circuit. Proceed to Test Step 4.
Not OK - The resistance measurements do not indicate an open circuit. There is a short circuit in the harness.Repair: Repair the connectors or wiring and/or replace the connectors or wiring.STOPTest Step 4. Check for an Open in the Harness
Use a suitable piece of wire to create a short circuit between the data link wires at one of the control modules on the CAN data link.
Measure the resistance between P1-50 and P1-34.
Measure the resistance at the connectors of any other control modules. Expected Result:The resistance measurement indicates a short circuit.Results:
OK - The resistance measurement indicates a short circuit. The CAN data link is OK.Repair: If the problem is intermittent, perform the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - The resistance measurement does not indicate a short circuit. There is an open circuit in the harness or connectors.Repair: Repair the connectors or wiring and/or replace the connectors or wiring.STOP


Parts coil Mercury:

835399
855944
COIL, Lighting
855944 COIL, Lighting
1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD
835399T
COIL, Charging
835399T COIL, Charging
1F10203VD, 1F10352VD, 1F13203FB
Back to top