73406A 1 Mercury COVER ASSEMBLY, SILENCER SERIAL


73406A 1 COVER ASSEMBLY, SILENCER SERIAL Mercury 1850506 COVER
73406A 1 COVER ASSEMBLY, SILENCER SERIAL Mercury
Rating:
88

Buy COVER ASSEMBLY, SILENCER SERIAL 73406A 1 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 35
 

Compatible models:

1850506   Mercury

Mercury entire parts catalog list:

1850506 1976,1977

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
B 9U-5023 Main Bearing Wrench 1
C 2P-5517 Main Bearing Tool 1
D 236-6688 Main Bearing Cap Tool 2
E 9S-7351 Torque Wrench 1
F 8T-5096 Dial Indicator Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the main bearings dry when clearance checks are preformed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.
Illustration 1 g01125211
Install lower main bearing (4) in main bearing cap (2). Ensure that the main bearing is installed so that the bearing tab fits into the notch in the main bearing cap. Note: The main bearing caps must be installed with the word "FRONT" and the part number toward the front of the engine. Each main bearing cap has a number on the bottom surface and each main bearing must be installed in the corresponding position in the cylinder block.
Install the upper main bearing with the side without the tab into the side of the cylinder block with the tab. Use your hand and roll the upper main bearing into position. Use Tooling (A) and rotate the crankshaft. Rotate the crankshaft until the oil hole is positioned in front of the side of the upper main bearing with the tab.
Illustration 2 g01125209
Install Tooling (C) and finish rolling the upper main bearing into position. Make sure that Tooling (C) does not slide under the upper main bearing. Ensure that the main bearing is installed so that the bearing tab fits into the notch in the cylinder block.
Remove Tooling (C).
The following step is for installing the thrust plates on each side of the center main bearing. Place clean engine oil on the thrust plates. Install the thrust plates on each side of the center main bearing. It may be necessary to move the crankshaft with a prybar in order to install a new thrust bearing. Use Tooling (F) to measure the end play of the crankshaft. The end play must not exceed 0.17 to 0.63 mm (0.007 to 0.025 inch).
Illustration 3 g01125192
Tighten the nuts on Tooling (D) in order to raise main bearing cap (2) to the cylinder block. The nuts must be tightened evenly in order for main bearing cap (2) to fit into the block.
Coat the underside of the bolt heads and the threads of bolts (3) with clean engine oil. Install the inner bolts for the main bearing cap. Remove Tooling (D) and install the outer bolts for the main bearing cap.
Illustration 4 g01139473
Illustration 5 g01124192
Bolt tightening sequence for the main bearing caps
Use Tooling (E) and Tooling (B) and tighten bolts (3) in sequence to a torque of 190 14 N m (140 10 lb ft).
Place an index mark on the bolts and the main bearing cap. Tighten the bolts for an additional 180 5 degrees (1/2 turn).
Rotate the crankshaft in order to ensure that the crankshaft turns freely.
Illustration 6 g01125228
Install side covers (1) onto the cylinder block. End By:
Install the oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".


Parts cover Mercury:

39667
 
39667 COVER, NYLON - SHIFT CABLE
1040208, 1080500, 1080508, 1090520, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1400100, 1402202, 1402205, 1650100, 1650502, 1650503, 1650506, 1700507, 1800100, 1850503
37417
 
37417 COVER, TRIM - DRIVE SHAFT HOUSING
1075524, 1080500, 1090520, 1090524, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1650100, 1800100, 1850503, 1850506
52699
 
52699 COVER, GEAR HOUSING
1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 11354120D, 1135412MD, 1140520, 1140528, 1140629, 1150453BD, 1150453GD, 1150453JD, 1150503, 1150538, 1150625, 1175413MD, 1650100, 1800
56029
 
56029 COVER, STARTER MOTOR BRACKET - TOP
1075524, 1080500, 1080508, 1090528, 1115100, 1115503, 1115525, 1115528, 1135100, 1140528, 1150503, 1150538, 1150625, 1850506
70679
 
70679 COVER, UPPER AND LOWER SHOCK MOUNTING PIN
1050200, 1070500, 1080500, 1090520, 1115503, 1115520, 1115523, 1115525, 1140520, 1150503, 1150625, 1500206, 1650503, 1650506, 1850503, 1850506
76867
 
76867 COVER, STARTER MOTOR BRACKET - BOTTOM
10402139D, 1045217, 1050200, 1070312BC, 1070717, 1075217DD, 1075217FD, 1075217PD, 1075217VD, 10752L7DF, 10752L7FF, 1075317DB, 1075317FB, 10754120D, 1075412DB, 1075412DD, 1075412DN, 1075412FB, 1075412FY, 1075524, 1080500, 1080508, 1090412DB, 1090412DC
74303
 
74303 COVER, AIR INLET
1075524, 1080500, 1080508, 1850506
76226A 1
Back to top