813547T 6 Mercury COWL LATCH LEVER (GRAY)


813547T 6 COWL LATCH LEVER (GRAY) Mercury 1050302SD, 1050312LD, 1055207UD COWL
813547T 6 COWL LATCH LEVER (GRAY) Mercury
Rating:
88

Buy COWL LATCH LEVER (GRAY) 813547T 6 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 42
 

Compatible models:

Mercury entire parts catalog list:

1050302SD 1996,1997
1050312LD 1991,1992,1993,1994,1995,1996
1055207UD 1998

Information:


Illustration 1 g00683014
This illustration represents the schematic for the "PTO Engine RPM Set Speed Input A" switch circuit.
Illustration 2 g00683021
This illustration represents the schematic for the "PTO Engine RPM Set Speed Input B" switch circuit.
Illustration 3 g00683028
Terminal Locations for ECMTest Step 1. Check the Electrical Connectors and the Wiring
Thoroughly inspect the ECM vehicle harness connector J1/P1, the connectors, and the firewall bulkhead connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the suspect switch circuit.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the harness and the wiring for abrasion and pinch points from the battery to the ECM. Then, check from the ignition key switch to the ECM.Refer to Illustration 3 for terminal locations for the ECM.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring should be free of corrosion, abrasion or pinch points.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the wiring and connectors or replace the wiring or the connectors. Ensure that all of the seals are properly connected.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Status of the "PTO Engine RPM Set Speed Input A" and "PTO Engine RPM Set Speed Input B" on ET
Connect the Caterpillar Electronic Technician (ET) to the cab data link connector.
Turn the ignition key switch to the ON position.
Operate the switch in the ON and OFF positions.
View the switch status on ET.
If the "PTO Engine RPM Set Speed Input A" status indicates "Not Installed", then the parameter has not been programmed. If the "PTO Engine RPM Set Speed Input B" status indicates "Not Installed", then the parameter has not been programmed.Expected Result:The status screen should indicate "ON" if the switch is turned on. The status screen should indicate "OFF" if the switch is off.Results:
OK - The switch is operating normally. Continue troubleshooting if the original condition is not resolved.STOP
Not OK - The ECM is not reading the switch status change. Proceed to Test Step 3.Test Step 3. Check the Switch Circuit for the ECM
Illustration 4 g00683037
Connector for Breakout T
Turn the ignition key switch to the OFF position.
Install a 70 terminal breakout T to the ECM vehicle harness connector J1/P1.
Fabricate a jumper wire 100 mm (4 inch) long. Crimp a Deutsch pin to both ends of the wire.
Insert the jumper wire into the suspect switch socket of the breakout T. Connect the other end of the jumper wire to terminal 5 (AP Sensor/Switch Common) in the breakout T.
Connect ET to the cab data link connector.
Turn the ignition key switch to the ON position.
Alternately remove the jumper wire and then insert the jumper wire from terminal 5. At the same time, monitor the status screen on ET.Expected Result:The switch status changes to "ON" with the jumper wire in place. The switch status changes to "OFF" when the jumper wire is removed.Results:
OK - The ECM is functioning properly at this time. Proceed to Test Step 4.
Not OK - The ECM is not functioning properly.Repair: Perform the following repair:
Temporarily connect a test ECM. Only connect ECM harness J1/P1.
Recheck for an +5 V diagnostic code when the engine harness is disconnected.
If the problem is resolved with the test ECM, reconnect the suspect ECM.
If the problem returns with the suspect ECM, replace the ECM.STOPTest Step 4. Insert a Jumper Wire at the Switch
Turn the ignition key switch to the OFF position.
Reconnect the ECM vehicle harness connector J1/P1.
Fabricate a jumper wire 100 mm (4 inch) long. Crimp a Deutsch pin to both ends of the wire.


Parts cowl Mercury:

813548A 3
 
813548A 3 COWL SUPPORT BRACKET (FRONT) (BLACK)
1050302SD, 1050312LD, 1055207DB, 1055207UD, 1055207VB
813548A 6
 
813548A 6 COWL SUPPORT BRACKET (FRONT) (SILVER)
1050302SD, 1050312LD, 1055207DB, 1055207UD, 1055207VB
813548A 5
813549A 2
 
813549A 2 COWL SUPPORT BRACKET (REAR)
1050302SD, 1050312LD, 1055207DB, 1055207UD, 1055207VB
813546 2
 
813546 2 COWL MOUNT
1041312UB, 10432037D, 1043203VD, 1050302SD, 1050312LD, 1055207UD, 1055207VB, 1090D73CD
813547T
 
813547T COWL LATCH LEVER (BLACK)
1050302SD, 1050312LD, 1055207DB, 1055207UD, 1055207VB
813547F 3
Back to top