828558 Mercury CRANK POSITION SENSOR


828558 CRANK POSITION SENSOR Mercury 1200473TD CRANK
828558 CRANK POSITION SENSOR Mercury
Rating:
78

Buy CRANK POSITION SENSOR 828558 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
 
£203.41
 

07-04-2018
13.73[5.85] pounds
VALEOSERVI: VALEOSERVICEDEUTSCHL
VALEO 828558 Clutch Sets
Number of teeth: 23||Supplementary Article/Info 2: with releaser||Part number: 828558
$55.50
 

13-03-2023
0.2[0.09] Pounds
-: -
#6 x 5/8" Flat Head # 2 Phillips Hinge Screw Nickel Plated Steel Platte River (1000-Pack)
Fastener size and finish match most european cabinet hinges and mounting plates. || Specifications: Drive=#2 PHILLIPS, Head Style=FLAT, Material=STEEL || Specifications: Point=SHARP, Screw Size=6, Threads=COARSE || Specifications: Screw Length=5/8 in, Finish=NICKEL, Quantity=100
$5.39
 

07-10-2018
20 Hundredths Pounds
Platte Riv: Platte River
Platte River 828558, Fasteners, Wood Screws, 6 X 5/8" Flat Head Phillips Np Hinge Screw, 100-pack
Fastener size and finish match most european cabinet hinges and mounting plates.||Specifications: Drive=#2 PHILLIPS, Head Style=FLAT, Material=STEEL||Specifications: Point=SHARP, Screw Size=6, Threads=COARSE||Specifications: Screw Length=5/8 in, Finish=NICKEL, Quantity=100
Number on catalog scheme: 28
 

Compatible models:

1200473TD   Mercury

Mercury entire parts catalog list:

1200473TD 1997

Information:

3. Fasten a hoist to fan assembly (1). Remove the bolts that hold the fan assembly to the fan drive. Lower the fan assembly to put it in position against the hydraulic oil cooler core. Weight of the fan assembly is 95 lb. (43 kg).
Do not cause damage to the hydraulic oil cooler core when the fan assembly is put in position against it.
4. Remove the three belts (2) from the fan drive.5. Disconnect the spring from the belt tightener. 6. Remove the two bolts and retainer that hold hub (3) in position.7. Hold pulley (4) in position and remove hub (3), then remove pulley (4). 8. Remove spacer (9) from the fan drive bracket.9. Remove the O-ring seal, bearings (5) and (7), spacer (6) and seal (8) from hub (3).10. Remove the belt tightener from the fan drive bracket. 11. Disconnect grease line (12) from the fan drive bracket.12. Remove bolts (10) and remove fan drive bracket (11). 13. Remove the spring and grease fitting from fan drive bracket (11).14. Remove the dowels that hold shafts (13) and (14) in position. Use a press and remove the shafts from the fan drive bracket.Install Fan Drive
1. Put the dowel holes in shafts (1) and (2) in alignment with the holes in fan drive bracket (3). Make sure the larger diameter hole in shaft (1) is opposite the threaded hole in bracket (3). Use a press and install the shafts in bracket (3).2. Install the dowels to hold shafts (1) and (2) in position. 3. Install the grease fitting and spring on bracket (3). Make sure nut (4) is tightened to a torque of 32 5 lb.ft. (43 7 N m).4. Put bracket (3) in position on the engine and install the bolts to hold it in position.5. Connect the grease line to bracket (3).6. Install the belt tightener on the fan drive bracket. Install the bolt and washer to hold the belt tightener in position. 7. Use tool (A) to install the seal even with the end of hub (5) with the lip of the seal toward the outside as shown.8. Install the smaller bearing in hub (5). 9. Install spacer (6) on the fan drive bracket with the chamfer toward the radiator. 10. Install pulley (7) on the fan drive bracket.11. Hold pulley (7) in position and install the hub and inner bearing on the fan drive bracket. 12. Install spacer (8), outer bearing (9) and the O-ring seal on the fan drive bracket.13. Install the retainer and two bolts that hold the bearings and hub to the fan drive bracket.14. Connect the spring to the belt tightener.15. Install the three belts on the fan drive.16. Use a hoist and lift fan assembly (10) into position. Install the bolts and nuts to hold the fan assembly to the fan drive. 17. Install fan guards (11).18. Install the channel assembly in the top of the radiator guard.19. Put clean grease in the fan drive and belt tightener.end by:a) install hood (rear)


Back to top