803515T Mercury CRANKSHAFT


803515T CRANKSHAFT Mercury 1B04201FB, 1F04201WB CRANKSHAFT
803515T CRANKSHAFT Mercury
Rating:
63

Buy CRANKSHAFT 803515T Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Mercury entire parts catalog list:

1B04201FB 2006
1F04201WB 2000,2001,2002,2003,2004,2005

Information:


Illustration 1 g03043497
Front view
Table 1
Specification for 354-5521 Cylinder Block Gp
Item Qty Part Specification Description
The top face of the cylinder block, bottom surface of spacer plate (2) and both sides of plate gasket (4) must be free of fuel, oil, water, gasket adhesives, assembly compounds and any other contaminants during assembly.
1 2 4W-4813 Plug Torque to 100 15 N m (74 11 lb ft).
2 16 110-6994 Spacer Plate Thickness is 12.313 mm (0.4848 inch).
3 32 8T-0099 Dowel Extension of the dowel is 21.0 0.5 mm (0.83 0.02 inch).
4 16 144-5692 Plate Gasket Thickness of plate gasket that is between cylinder block and spacer plate is 0.194 to 0.218 mm (0.0076 to 0.0086 inch).
5 16 197-7008 Dowel Extension of the dowel is 21.0 0.5 mm (0.83 0.02 inch).
A 18 116-1359 Camshaft Bearing Bore in the block for the camshaft bearing is 98.000 0.020 mm (3.8583 0.0008 inch).
B - - All centerlines through oil holes in the camshaft bearings and the camshaft bearing junctions (6) are shown for each side of the cylinder block.
Oil holes must be positioned from horizontal at an angle of 20.0 0.5 degrees.
C - - New dimension from centerline of crankshaft bearing bore to the top of the block is 586 mm (23.1 inch).
7 8 6V-3348 O-Ring Seal Lubricate the bore lightly with sealant that is being sealed.
8 9 223-1696 Crankshaft Bearing Cap Install crankshaft bearing caps with the part number and FRONT toward the front of the block. Each cap has a number. Each cap must be installed in the same position as the correct number on the side of the cylinder block pan rail.
Width (D) of crankshaft bearing cap is 340.030 0.015 mm (13.3870 0.0006 inch).
Width in the cylinder block for crankshaft bearing cap is 339.985 0.015 mm (13.3852 0.0006 inch).
- - - Bore (E) in the block for the crankshaft bearings is 169.742 0.020 mm (6.6827 0.0008 inch).
- - - New dimension (F) from centerline of crankshaft bearing bore to bottom of block (pan rails) is 230.00 mm (9.055 inch).
9 36 7X-7925 Bolt Use the following procedure in order to tighten the crankshaft bearing cap bolts.
1. Lubricate the threads with clean engine oil before assembly.
2. Tighten the bolts by hand.
2. Tighten the bolts in the numerical sequence as shown in Illustration 1 to 190 14 N m (140 10 lb ft).
3. Again tighten the bolts in the numerical sequence as shown in Illustration 1 to an angle of 180 5 degrees.
Illustration 2 g03043498
Right side view
Table 2
Item Qty Part Specification Description
G 1 7N-2047 Dowel Extension of the dowel is 6.0 0.5 mm (0.24 0.02 inch).
H 2 7N-2047 Dowel Extension of the dowel is 6.0 0.5 mm (0.24 0.02 inch).
J 2 4N-0683 Dowel Extension of the dowel is 19.0 0.5 mm (0.75 0.02 inch).
K 2 7N-2044 Dowel Extension of the dowel is 40.0 0.5 mm (1.58 0.02 inch).
10 4 5F-9657 O-Ring Seal Lubricate the bore lightly with sealant that is being sealed.
11 3 7X-4805 O-Ring Seal Lubricate the bore lightly with sealant that is being sealed.
12 2 5P-8210 O-Ring Seal Lubricate the bore lightly with sealant that is being sealed.


Back to top