824093A96 Mercury DECAL SET


824093A96 DECAL SET Mercury 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1040213YL, 1041312UB DECAL
824093A96 DECAL SET Mercury
Rating:
73

Buy DECAL SET 824093A96 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Mercury entire parts catalog list:

1031203PD 1994,1995,1996,1997,1998,1999
1031203UB 1998,1999,2000,2001,2002,2003,2004
1031203UD 1998,1999
1031207ZF 2002
1040213YL 2001,2004
1041312UB 1998

Information:


Illustration 1 g00970385
Schematic
Illustration 2 g00970387
P2 ECM connector
Illustration 3 g00810608
Sensor connectorTest Step 1. Disconnect the ECM Connector and Check for Active Diagnostic Codes
Turn the keyswitch to the OFF position.
Connect the Caterpillar Electronic Technician (Cat ET) to the data link connector.
Disconnect the P2 ECM connector from the ECM.
Check the ECM connector for corrosion and moisture.
Turn the keyswitch to the ON position.
Check for active diagnostic codes on Cat ET.Note: A "voltage high" diagnostic code (open circuit) should be active for all of the engine pressure sensors.Expected Result:The 5 volt diagnostic codes are not active. A "voltage high" diagnostic code (open circuit) is active for all of the engine pressure sensors.Results:
OK - The 5 volt diagnostic codes are not active.Repair: Reconnect the P2 ECM connector. Proceed to Test Step 2.
Not OK - The 5 volt diagnostic codes are still active.Repair: Connect a test ECM.If the test ECM fixes the problem, reconnect the suspect ECM.If the problem returns, permanently install the new ECM.Verify that the repair eliminates the problem.STOPTest Step 2. Disconnect the Sensors
Turn the keyswitch to the ON position.
Monitor the active diagnostic code screen on Cat ET.
Disconnect the pressure sensors one at a time. Wait for 30 seconds after each pressure sensor is disconnected.Note: The 5 volt diagnostic code will become inactive if a pressure sensor is the cause of the 5 volt diagnostic code.
Ensure that all of the pressure sensors are disconnected.Expected Result:The 5 volt diagnostic code is still active when all of the pressure sensors are disconnected.Results:
OK - The 5 volt diagnostic code is still active.Repair: Leave all of the pressure sensors disconnected. Proceed to Test Step 4.
Not OK - The 5 volt diagnostic code disappears when the pressure sensors are disconnected. Repair: Reconnect all of the pressure sensors except the suspect sensor. Proceed to Test Step 3.Test Step 3. Check the Signal Wire
Turn the keyswitch to the ON position.Note: The suspect sensor should be disconnected.
Measure the voltage between terminal C (Signal) and terminal B (Pressure Sensor Common) of the connector for the suspect sensor on the engine harness.Expected Result:The voltage is less than 7.0 VDC.Results:
OK - The voltage is within the range.Repair: Temporarily connect a new sensor.If the problem is resolved with the new sensor, reconnect the suspect sensor.If the problem returns, replace the suspect sensor.Verify that the repair eliminates the problem.STOP
Not OK - The voltage is greater than 7.0 VDC.Repair: Inspect the signal wire for a short circuit to a voltage source.Repair the signal wire or replace the signal wire.Verify that the repair eliminates the problem.STOPTest Step 4. Determine the Condition that is Present
Turn the keyswitch to the ON position.
Access the active diagnostic code screen on Cat ET.Expected Result:232-03 or 232-04 is active.Results:
232-03 - Proceed to Test Step 5.
232-04 - Proceed to Test Step 7.Test Step 5. Measure the 5 Volt Supply to the Sensor
Turn the keyswitch to the ON position.Note: All of the pressure sensors should be disconnected.
Measure the voltage between terminal A (Pressure Sensor +5V) and chassis ground for each pressure sensor.Expected Result:The voltage is 5.0 0.16 VDC.Results:
OK - The 5 volt supply is within the range. Proceed to Test Step 6.
Not OK - The voltage is greater than 5.16 volts.Repair: Check the 5 volt supply wire for a short to a higher voltage source.Repair the 5 volt supply wire or replace the 5 volt supply wire.Verify that the repair eliminates the problem.STOPTest Step 6. Check the Common Wire
Turn the keyswitch to the ON position.
Measure the voltage between terminal A (Pressure Sensor +5V) and terminal B (Pressure Sensor Common) on all of the pressure sensors.
While the voltage is monitored, perform a 45 N (10 lb) pull test on the common wires for the 5 volt supply.
P2:3 (Pressure Sensor Common)
P2:42 (Pressure Sensor Common (Actuator))Expected Result:The voltage is 5.0 0.16 VDC.Results:
OK - The voltage is within the range.Repair: If the problem is intermittent, refer to Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - The voltage is not within the range.Repair: Inspect the common wire for an open circuit.Repair the common wire or replace the common wire.Verify that the repair eliminates the problem.STOPTest Step 7. Check the Resistance of the Harness
Turn the keyswitch to the OFF position.
Verify that all of the sensors are disconnected.
Measure the resistance between terminal A (Pressure Sensor +5V) and terminal B (Pressure Sensor Common) of each connector for the pressure sensor on the engine harness.Expected Result:The resistance is greater than 20,000 Ohms, or "OL" is displayed on the multimeter.Results:
OK - The 5 volt supply and the pressure sensor common are not shorted.Repair: Check the 5 volt supply for a short to ground.Repair the 5 volt supply wire or replace the 5 volt supply wire.Verify that the repair eliminates the problem.STOP
Not OK - There is a short between the 5 volt supply and the pressure sensor common.Repair: Locate the short between the 5 volt supply and the pressure sensor common.Repair the faulty wiring or replace the faulty wiring.Verify that the repair eliminates the problem.STOP


Parts decal Mercury:

824200 2
 
824200 2 DECAL
1006201DB, 1006201PD, 1006201RB, 1006201VB, 1006211RD, 1008211RD, 1010207VB, 1011201DB, 1016207PD, 1016207RB, 10202014D, 1020201DB, 1020201VB, 1031203PD, 1031203UD, 1041312UB, 1F08203VF, 1F08261RF, 1F10352VD
808616A94
 
808616A94 DECAL SET
1031203PD, 1031203UD, 1041312UB
808616A96
 
808616A96 DECAL SET
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1040213YL, 1041312UB
830253
 
830253 DECAL-TILT/LOCK
1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312FB, 1050411DD, 1050412DB, 1050412DD, 1050412FB, 1050412F
855577 8
 
855577 8 DECAL-EPA INFO (TOP COWL INLET DUCT)(
1041312UB, 10432037D, 1055207UD
808615A01
 
808615A01 DECAL SET
1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL
808682A01
 
808682A01 DECAL SET
1031203UB, 1031203UD, 1031207ZF, 1040213YL
853797A00
 
853797A00 DECAL SET
1030201YL, 1031207ZF
Back to top