858842001 Mercury DECAL, Gang Run


858842001 DECAL, Gang Run Mercury 1040203YL, 1040213YL DECAL
858842001 DECAL, Gang Run Mercury
Rating:
78

Buy DECAL, Gang Run 858842001 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 0
 

Compatible models:

Mercury entire parts catalog list:

1040203YL 2001,2002,2003,2004
1040213YL 2001,2004

Information:

Drain the coolant systems
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Cat Dealer Service Tool Catalog" or refer to Special Publication, PECJ0003, "Cat Shop Supplies and Tools Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Stop the engine and allow the engine to cool. Ensure that the engine will not start when the cooling system is drained.
Loosen the cooling system filler caps slowly in order to relieve any pressure. Remove the cooling system filler caps.
Open the cooling system drains.Note: If equipped, be sure to drain the heater and any related supply and return lines.Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Cat dealer or consult Cat Dealer Service Tool Group:Inside USA 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
International 1-309-578-7372
Jacket Water System
Illustration 1 g03163458
Oil cooler outlet bonnet drain
Illustration 2 g03163459
Jacket water heat exchanger drain (Some parts removed for visibility)
SCAC System
Illustration 3 g03163537
SCAC pump outlet bonnet drain
Illustration 4 g03163460
SCAC heat exchanger drain
Radiator System
Illustration 5 g03562899
(1) Jacket water outlet drain valve
(2) SCAC outlet drain valve
(3) SCAC inlet drain valveFlush
Systems Filled with Cat ELC, Cat ELI, or a Conventional Coolant that Meets the Cat EC-1 Requirements and the Standards of ASTM D6210
Flush the cooling system with clean water in order to remove any debris.
Close the drain valves (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual, SENR3130, "Torque Specifications" for more information on the proper torques.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with clean water. Install the cooling system filler cap.
Start and run the engine at low idle until the temperature reaches 49 to 66 °C (120 to 150 °F).
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valves (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valves (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual, SENR3130, "Torque Specifications" for more information on the proper torques.Systems Filled with Cat DEAC, Conventional Coolant which does not Meet the Cat EC-1 Requirements, or Supplemental Coolant Additive (SCA) and Water
Flush the cooling system with clean water in order to remove any debris.
Close the drain valves (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual, SENR3130, "Torque Specifications" for more information on the proper torques.


Parts decal Mercury:

804664A00
 
804664A00 DECAL, EPA Information
1031203UB, 1031203UD, 1031207ZF, 1040213YL
804664A01
 
804664A01 DECAL, EPA Information
1031203UB, 1031203UD, 1031207ZF, 1040213YL
804664A02
 
804664A02 DECAL, EPA Information
1031203UB, 1031203UD, 1031207ZF, 1040213YL
808683A01
 
808683A01 DECAL SET
1031203UB, 1031203UD, 1031207ZF, 1040213YL
808615A01
 
808615A01 DECAL SET
1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL
808682A01
 
808682A01 DECAL SET
1031203UB, 1031203UD, 1031207ZF, 1040213YL
802987
DECAL
802987 DECAL
1030201YL, 1031207ZF, 1040203FL, 1040203YL, 1040213YL
855973A98
 
855973A98 DECAL SET
1040203YL, 1040213YL
Back to top