859595T Mercury DRIVER, Dual Coil


859595T DRIVER, Dual Coil Mercury 111047JHD, 1135473YD, 1135D73CD, 1135D73FT, 1200473YD, 1200D73AD, 1200D73CD, 1200D73HT, 1200E73HY, 1225E73AD, 1225P73DD DRIVER
859595T DRIVER, Dual Coil Mercury
Rating:
8

Buy DRIVER, Dual Coil 859595T Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$128.99
 

30-03-2022
0.20062065842[0.00] Pound
-: -
MERCURY DRIVER-DUAL COIL
Number on catalog scheme: 9
 

Mercury entire parts catalog list:

111047JHD 2006
1135473YD 2001,2002,2003
1135D73CD 2004,2005
1135D73FT 2006
1200473YD 2001,2002
1200D73AD 2003
1200D73CD 2004,2005,2006
1200D73HT 2006
1200E73HY 2006
1225E73AD 2003,2004,2005,2006
1225P73DD 2005,2006

Information:


Table 1
Troubleshooting Test Steps Values Results
1. Extended Idle Times
A. Extended idle times will allow oil to pass into the exhaust system.
Idle times
Result: The idle times are extensive.
Repair: Reduce the idle times.
Proceed to Test Step 6.
Result: The idle times are not extensive.
Proceed to Test Step 2.
2. Failed Turbocharger Seals
A. Check the inlet manifold and the exhaust manifold for oil.
Turbo seals
Result: Oil is present in the inlet or exhaust manifold.
Repair: Replace the turbocharger. Verify the repair.
Proceed to Test Step 6.
Result: Oil is not present in the inlet or exhaust manifold.
Proceed to Test Step 3.
3. Worn Valve Guide Seals or Faulty Valve Guide Seals
A. Inspect the valve guide seals for wear and for damage.
Valve guide seals
Result: The valve guide seals are damaged.
Repair: Replace the valve guide seals. Verify the repair.
Proceed to Test Step 6.
Result: The valve guide seals are not damaged.
Proceed to Test Step 4.
4. Worn Valve Guides
A. Inspect the valve guides for wear. Refer to the Specification manual for the maximum permissible wear of the valve guides.
Valve guides
Result: The valve guides are worn.
Repair: If necessary, recondition the cylinder head. Verify the repair.
Proceed to Test Step 6.
Result: The valve guides are not worn.
Proceed to Test Step 5.
5. Worn Piston Rings
A. Remove the pistons. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Remove".
B. Remove the piston rings from the pistons. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Disassemble"
C. Inspect the pistons and piston rings for wear or damage. Refer to the "Specifications" manual for further information.
Piston rings
Result: The piston rings are worn.
Repair: Replace the piston rings. Verify the repair.
Proceed to Test Step 6.
Result: The piston rings are not worn.
Contact the Dealer Solutions Network (DSN).
6. Check the Aftertreatment System for Oil
A. Remove excess oil from piping with a clean cloth.
B. Remove the Clean Emissions Module (CEM). Refer to Disassembly and Assembly, "Clean Emissions Module - Remove and Install".
C. Support the CEM over a suitable container with the exhaust inlet downwards. Leave the CEM to drain for 8 hours.
D. Check the quantity of drained oil in the container.
CEM
Result: The volume of drained oil is greater than 1.0 L (1.05669 qt).
Repair: Install a replacement CEM. Refer to Disassembly and Assembly, "Clean Emissions Module - Remove and Install".
Return the unit to service.
Result: The volume of drained oil is less than 1.0 L (1.05669 qt).
Proceed to Test Step 7.
7. Recover the Aftertreatment System
A. Clean any remaining oil from the piping and the CEM inlet with a clean cloth.
B. Install the Clean Emissions Module (CEM). Refer to Disassembly and Assembly, "Clean Emissions Module - Remove and Install".
C. Run the engine at high idle with no load for a minimum of 20 minutes.
D. Use the electronic service tool to perform the "Aftertreatment Recovery Procedure". While the procedure is progressing, check for smoke from the exhaust. Some smoke will be evident during the procedure. The smoke must dissipate before the procedure is completed.
CEM
Result: The "Aftertreatment Recovery Procedure" completes with a soot load of less than 80% and no smoke from the exhaust.
Return the unit to service.
Result: The "Aftertreatment Recovery Procedure" completes with a soot load of more than 80% or smoke from the exhaust.
Contact the Dealer Solutions Network (DSN).


Parts driver Mercury:

37323
 
37323 DRIVER HEAD ROD
1002201FM, 1002201JK, 1002201VB, 1003201NK, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312F
55919
 
55919 DRIVER HEAD
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312FB, 1050411DD, 1050412DB, 1050412DD, 1050412F
816244
DRIVER TOOL, Bearing
816244 DRIVER TOOL, Bearing
1200453CD, 1200453EY, 1200453HY, 1200473UD, 1200473VD, 1200473WD, 1200473YD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225412PD, 1225412VD, 1225413EY, 1225413RD, 1225413ZD, 1225423EY, 1225424EY, 1225E73AD, 1250413CD, 1250413U
33491
 
33491 DRIVER
1200453CD, 1200453EY, 1200453HY, 1200473UD, 1200473VD, 1200473WD, 1200473YD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225412PD, 1225412VD, 1225413EY, 1225413RD, 1225413ZD, 1225423EY, 1225424EY, 1225E73AD, 1250413CD, 1250413U
87120T
 
87120T DRIVER TOOL, Bearing Cup (GEAR HOUSING)
111047JHD, 1115473WD, 1135412WD, 1135473VD, 1135473YD, 1135D73CD, 1135D73FT, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413WD, 1150413ZD, 1150423FG, 1150423FY, 1150423HF, 1150423HG, 1150423HY, 1150424FY, 1150424HY, 1175P73HY, 1200413FY, 1200413H
36577T
 
36577T DRIVER CUP (GEAR HOUSING)
1200453CD, 1200453EY, 1200453HY, 1200473VD, 1200473WD, 1200473YD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225412VD, 1225413EY, 1225413ZD, 1225423EY, 1225424EY, 1225E73AD, 1250413CD, 1250413UE, 1250424EY, 1250433EY, 1250434E
31108T
DRIVER, Oil Seal (GEAR HOUSING)
31108T DRIVER, Oil Seal (GEAR HOUSING)
1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312FB, 1050411DD, 1050412DB, 1050412DD, 1050412FB, 1050412FD, 1055207DB, 1055207VB, 1075217DD, 1075217FD, 1075217VD, 10752L7DF, 10752L7F
817569T
 
817569T DRIVER TOOL, Oil Seal (GEAR HOUSING)
1200453CD, 1200453EY, 1200453HY, 1200473VD, 1200473WD, 1200473YD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225412VD, 1225413EY, 1225413ZD, 1225423EY, 1225424EY, 1225E73AD, 1250413CD, 1250413UE, 1250424EY, 1250433EY, 1250434E
Back to top