87120 Mercury DRIVER TOOL, Bearing Cup


87120 DRIVER TOOL, Bearing Cup Mercury 1135412SD, 1135412VD, 1135473UD, 1150413SD, 1150413VD, 1225412PD, 1225413RD DRIVER
87120 DRIVER TOOL, Bearing Cup Mercury
Rating:
103

Buy DRIVER TOOL, Bearing Cup 87120 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Mercury entire parts catalog list:

1135412SD 1996,1997,1998
1135412VD 1999
1135473UD 1998
1150413SD 1996,1997,1998
1150413VD 1999
1225412PD 1994,1995,1996,1997,1998
1225413RD 1995,1996,1997,1998

Information:

This procedure checks for air in the fuel system. This procedure also helps with finding the source of the air.
Examine the fuel system for leaks. Ensure that the fuel line fittings are properly tightened. Check the fuel level in the fuel tank. Air can enter the fuel system on the suction side between the fuel transfer pump and the fuel tank.
Work carefully around an engine that is running. Engine parts that are hot, or parts that are moving, can cause personal injury.
Install a 2P-8278 Fuel Flow Tube (Sight Gauge) in the fuel return line. When possible, install the sight gauge in a straight section of the fuel line that is at least 304.8 mm (12 inches) long. Do not install the sight gauge near the following devices that create turbulence:
Elbows
Relief valves
Check valvesObserve the fuel flow during engine cranking. Look for air bubbles in the fuel. If there is no fuel that is present in the sight gauge, prime the fuel system. Refer to Operation and Maintenance Manual, "Fuel System Priming Pump - Operate" for more information. If the engine starts, check for air in the fuel at varying engine speeds. When possible, operate the engine under the conditions which have been suspect.
Illustration 1 g00578151
2P-8278 Fuel Flow Tube (Sight Gauge)
(1) A steady stream of small bubbles with a diameter of approximately 1.60 mm (0.063 inch) is an acceptable amount of air in the fuel.
(2) Bubbles with a diameter of approximately 6.35 mm (0.250 inch) are also acceptable if there is two seconds to three seconds intervals between bubbles.
(3) Excessive air bubbles in the fuel are not acceptable.
If excessive air is seen in the sight gauge in the fuel return line, install a second sight gauge at the inlet to the fuel transfer pump. If a second sight gauge is not available, move the sight gauge from the fuel return line and install the sight gauge at the inlet to the fuel transfer pump. Observe the fuel flow during engine cranking. Look for air bubbles in the fuel. If there is no fuel that is present in the sight gauge, prime the fuel system. Refer to Testing and Adjusting, "Fuel System - Prime" for more information. If the engine starts, check for air in the fuel at varying engine speeds.If excessive air is not seen at the inlet to the fuel transfer pump, the air is entering the system after the fuel transfer pump. Refer to the Testing and Adjusting, "Fuel System - Prime".If excessive air is seen at the inlet to the fuel transfer pump, air is entering through the suction side of the fuel system.
To avoid personal injury, always wear eye and face protection when using pressurized air.
To avoid damage, do not use more than 55 kPa (8 psi) to pressurize the fuel tank.
Pressurize the fuel tank to 35 kPa (5 psi). Do not use more than 55 kPa (8 psi) to avoid damage to the fuel tank. Check for leaks in the fuel lines between the fuel tank and the fuel transfer pump. Repair any leaks that are found. Check the fuel pressure to ensure that the fuel transfer pump is operating properly. For information about checking the fuel pressure, see Testing and Adjusting, "Fuel System Pressure - Test".
If the source of the air is not found, disconnect the supply line from the fuel tank and connect an external fuel supply to the inlet of the fuel transfer pump. If this corrects the problem, repair the fuel tank or the stand pipe in the fuel tank.


Parts driver Mercury:

37323
 
37323 DRIVER HEAD ROD
1002201FM, 1002201JK, 1002201VB, 1003201NK, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312F
55919
 
55919 DRIVER HEAD
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312FB, 1050411DD, 1050412DB, 1050412DD, 1050412F
36569
 
36569 DRIVER HEAD
1041312UB, 10432037D, 1055207UD, 1075217PD, 1100412PD, 1135412SD, 1135412VD, 1135473UD, 1135473VD, 1150413SD, 1150413VD, 1200473UD, 1200473VD, 1225412PD, 1225413RD
816244
DRIVER TOOL, Bearing
816244 DRIVER TOOL, Bearing
1200453CD, 1200453EY, 1200453HY, 1200473UD, 1200473VD, 1200473WD, 1200473YD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225412PD, 1225412VD, 1225413EY, 1225413RD, 1225413ZD, 1225423EY, 1225424EY, 1225E73AD, 1250413CD, 1250413U
36577
 
36577 DRIVER TOOL, Bearing Cup
1200473UD, 1225412PD, 1225413RD
33491
 
33491 DRIVER
1200453CD, 1200453EY, 1200453HY, 1200473UD, 1200473VD, 1200473WD, 1200473YD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225412PD, 1225412VD, 1225413EY, 1225413RD, 1225413ZD, 1225423EY, 1225424EY, 1225E73AD, 1250413CD, 1250413U
817569
 
817569 DRIVER TOOL, Oil Seal
1200473UD, 1225412PD, 1225413RD
Back to top