71191 Mercury ELBOW, CRANKCASE VENT (PRESS IN)


71191 ELBOW, CRANKCASE VENT (PRESS IN) Mercury 1018200, 1018204, 1025200, 1060504, 1070500, 1225620, 1700507 ELBOW
71191 ELBOW, CRANKCASE VENT (PRESS IN) Mercury
Rating:
58

Buy ELBOW, CRANKCASE VENT (PRESS IN) 71191 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Compatible models:

Mercury entire parts catalog list:

1018200 1980,1982,1983
1018204 1984,1985,1986,1987
1025200 1980,1982,1983
1060504 1984,1985,1986,1987
1070500 1980,1982,1983
1225620 1980
1700507 1977,1978,1979

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 487-8643 Tool As 1
B 339-9353 Cap Kit 1
265-2256 Lint Free Wipes 1
C 246-8191 Socket 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not open the high pressure fuel system without allowing the fuel system to purge. After the engine has shut down, allow the fuel system to purge for ten minutes. This operating fuel system contains high pressure. Exposure to high pressure fuel can result in personal injury.
Note: Use Tooling (B) to cap tube assemblies, fittings, ports, and any openings on the fuel system to prevent contamination.Note: When replacing the fuel pump, replace the oil screen in the fuel pump adaptor.
Illustration 1 g03871386
Remove clamp assembly (8), hose assembly (1), hose assembly (2), hose assembly (4), and hose assembly (3). Remove clamp assembly (7) and hose assembly (6). Disconnect harness assembly (5).
Illustration 2 g03871410
Remove bolt (11). Disconnect harness assembly (16) from the fuel pump.
Remove tube assembly (9) and hose assembly (10).
Remove bolts (12) and plate assembly (11).
Remove bolts (13) and bracket assembly (14).
Illustration 3 g03871453Note: When the fuel lines are removed, use clean engine oil to lubricate the outside diameter of tube assembly (22) in Area (X). Use Tooling (C) to remove bolts (18) and (21). Contamination and fuel leaks may occur If the procedure is not followed.
Remove bolt (23) and clamp assembly (19). Remove and discard bolts (18) and bolts (21).
Remove tube assembly (22) and the O-ring seals.
Illustration 4 g06301855
Typical Example
Use Tooling (A) and attach a suitable lifting device onto fuel pump (17). The weight of fuel pump (17) is approximately 157 kg (346 lb). Refer to Tool Operating Manual, M0080739 , "HPFP". Remove bolts (20). Lower fuel pump (17) to the ground.Note: The lifting device should not come into contact with the fuel shutoff valve which will result in damage to the component.! Magnetic lift of the high-pressure fuel pump is prohibited.
Illustration 5 g03871734
Remove bolts (24), bolts (26), fuel manifold (25), fuel transfer pump (27).
Illustration 6 g03871901
Remove and discard oil screen (28).Installation Procedure
Install fuel pump (17) in the reverse order of removal.
Install new oil screen (28).
Lubricate the O-ring seals with clean engine oil. Lubricate the ends of tube assembly (22) with clean engine oil. Install the O-ring seals on tube assembly (22). Install tube assembly (22). Install new bolts (21) hand tight. Install new bolts (18) hand tight. Position clamp assembly (19). Install bolt (23). Use Tooling (C) and evenly tighten bolts (21) to a torque of 20 N m (177 lb in). Use Tooling (C) and evenly tighten bolts (18) to a torque of 20 N m (177 lb in).
Evenly tighten bolts (21) to a torque of 40 N m (30 lb ft). Evenly tighten bolts (18) to a torque of 40 N m (30 lb ft). Tighten bolt (23).Note: Do not rotate bolts (21) and (18) more than 45 degrees at a time.


Parts elbow Mercury:

99664
 
99664 ELBOW (90 )(40-SER.33028361 & UP)
1005200, 1006206, 1007209, 1008211RD, 1016207PD, 1016207RB, 1016207SB, 1018204, 10202014D, 1020201BC, 1031203PD, 1031203UD, 1040100, 10402139D, 1041312UB, 1045217, 1050200, 1050302SD, 1050312BC, 1050312LD, 1060504, 1070312BC, 1070500, 1070717, 107521
25885
 
25885 ELBOW, TELL TALE - CYLINDER BLOCK
1007208, 1010208, 1018200, 1020100, 1020208, 1025200, 1040102, 1045205, 1075101, 1075202, 1075204, 1080500, 1080508, 1090520, 1110100, 1110102, 1110204, 1115100, 1115503, 1115520, 1115523, 1115525, 1135100, 1140520, 1140629, 1150503, 1150625, 1200203
54090
 
54090 ELBOW, FUEL PUMP OUTLET
1020100, 1020202, 1075101, 1110100, 1200628, 1225620
78279
 
78279 ELBOW, TELL TALE HOSE TO CYLINDER BLOCK
1035204, 1035207, 1040200, 10402139D, 1045217, 1050200, 1050302SD, 1050312LD, 1055207UD, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 1115520, 1115523, 1115525, 1115528, 1135473UD, 1140520, 1140528, 1140629, 1150413ZD, 1150538, 1225412PD, 12
7901
 
7901 ELBOW
11354120D, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1150453JD, 1200412GD, 1200628, 1225412PD, 1225412VD, 1225620
Back to top